background image

3

TABLE OF CONTENTS

Gas supply adjustments
(Commissioning Part II)

Servicing

Fault Finding

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Indicator lights  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Logical fault finding procedure  . . . . . . . . . . . . . . . . . .73
Status mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Diagnostic modes  . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Fault codes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Fault memory  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Fault finding charts  . . . . . . . . . . . . . . . . . . . . . . . . . .78

Diagrams

Functional flow diagrams  . . . . . . . . . . . . . . . . . . . . . .85
Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

Short parts list

Short parts list  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Initial inspection  . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Cleaning the burner and primary heat exchanger  . . . . . .58

Parts replacement

Safety instructions  . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Initial preparation  . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Burner  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Electrodes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Fan

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Gas valve  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Temperature sensors (NTCs)  . . . . . . . . . . . . . . . . . . . .63
Main heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . .63
Expansion vessel  . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Electronic control board  . . . . . . . . . . . . . . . . . . . . . . .65
Main transformer  . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Pump  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Air pressure switch  . . . . . . . . . . . . . . . . . . . . . . . . . .66
Automatic bypass  . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Pressure gauge  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Diverter valve (TURBOmax Plus only)  . . . . . . . . . . . . . .68
Aqua sensor (TURBOmax Plus only)  . . . . . . . . . . . . . . .68
DHW heat exchanger (TURBOmax Plus only)  . . . . . . . . .69
Pressure relief valve  . . . . . . . . . . . . . . . . . . . . . . . . . .69
Checking functions  . . . . . . . . . . . . . . . . . . . . . . . . . .70

Functional checks
(Commissioning Part III)

Functional checks  . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Functional check of operation  . . . . . . . . . . . . . . . .53/54
Adjusting pump speed  . . . . . . . . . . . . . . . . . . . . . . . .55

Final system flush (hot) . . . . . . . . . . . . . . . . . . . .55

Handing over to the user  . . . . . . . . . . . . . . . . . . . . . .56

Gas inlet working pressure  . . . . . . . . . . . . . . . . . . . . .44
Main burner pressure . . . . . . . . . . . . . . . . . . . . . . . . .45
Adjusting the central heating output (range rating)  . . . . .46
Adjusting the ignition rate . . . . . . . . . . . . . . . . . . . . . .48
Adjusting to the maximum heat load (nominal load)  . . . .49
Burner pressure and gas rate . . . . . . . . . . . . . . . . .50/51

Commissioning Part I

Preliminary electrical checks  . . . . . . . . . . . . . . . . . . . .39
Gas supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Cold water supply (TURBOmax Plus only)  . . . . . . . . . . .39
Filling the heating system (TURBOmax Plus)  . . . . . . . . . .40
Filling the heating system (THERMOcompact)  . . . . . . . . .42
Initial system flush (`cold`)  . . . . . . . . . . . . . . . . . . .41/43

TURBO

max

Summary of Contents for THERMOcompac SERIES





























































































Reviews: