background image

Start-up 8

0020149486_04 auroFLOW plus Installation and maintenance instructions

23

8.4

Test menu

As well as the installation assistants, you can also call up the
test menu for start-up, maintenance and troubleshooting.

Menu

Installer level

Test menu

This contains

Statistics

,

Check programmes

and the

Sensor/actuator test

.

8.4.1

Statistics

Menu

Installer level

Test menu

Statistics

This displays the operating hours for:

Solar pump

Solar pump 2

Cylinder pump

8.4.2

Check programmes

Menu

Installer level

Test menu

Check pro-

grammes

The following check programmes are available:

Test solar circuit filling

Start purging programme

8.4.3

Sensor/ actuator test

Menu

Installer level

Test menu

Sensor/actuator

test

The current values of the following sensors can be read off
here:

T1 temperature sensor

T2 temperature sensor

T3 temperature sensor

T4 temperature sensor

T5 collector sensor

T6 cylinder sensor

Cylinder circuit flow rate

Temperature limiter

Solar circuit flow rate

The selection button can be used to activate the following
actuators. You can then use the plus and minus buttons to
change the output/power of the pumps, the flow direction
of the shift-load switching valve or the stratification in the
cylinder.

Solar pump

Solar pump 2

Cylinder pump

UV5 shift-load switching valve

In addition, you can view the approximate

Solar circuit flow

rate

. The value is calculated from the pump output and rota-

tional speed.

8.5

Configuration

You can use the menu

Configuration

to subsequently

change the settings that have been made using the
installation assistant.

Language

Contact details

Date

Time

Summer/winter time

Cascade

Number of collectors

In addition, the following information can be set or read:

Filling time correction

Mode

Heating flow set target temperature

Hot water set target temperature

Shift-load switching valve switch temperature

Maximum cylinder temperature

On temp. diff.

eBUS control

Filling power

Compensation time

Software version

8.5.1

Filling time correction

Menu

Installer level

Configuration

Filling time

corr.

If the filling time is not sufficient for the solar circuit, the filling
time can be extended by up to ten minutes.

8.5.2

Mode

Note

If a system controller is connected, this menu
point does not appear.

Menu

Installer level

Configuration

Operating mode

The operating mode can be set to

Auto

,

High Flow

and

Low Flow

.

Auto

: The solar control attempts to maintain the spread

between the solar supply pipe and the solar return so
that the process water zone in the cylinder is charged at
65 °C. If this is not possible due to low solar radiation, the
heating zone in the cylinder is charged at 40 °C. If this is
not possible either, a spread of 10 K is attempted.

High Flow

: The solar control attempts to maintain the

spread between the solar supply pipe and the solar re-
turn at approx. 10 K. As a rule, this corresponds to 40 l/h
per m

2

collector surface

Low Flow

: The solar control attempts to maintain the

spread between the solar supply pipe and solar return so
that the cylinder is charged at the maximum set cylinder
temperature. As a rule, this corresponds to 15 l/h per m

2

collector surface

Summary of Contents for auroFLOW plus VPM 15 D





































Reviews: