Vaderstad Spirit R Quick Start Manual Download Page 7 | Manualshive

Page: 7 / 20

background image

7

01.03.2017

STR 300S

Settings

8a. Following harrow - “Heavy” model

The weight of the “heavy” following harrow is relived from E-Control. The following harrow can also be set

with different angles of attack to the soil:

Normal position

Light conditions/a lot of straw

Hard conditions/no straw

7. Light soil kit (accessory)

Adjust the rubber rods so that they are away from the bank that can form between the repacking wheels on light

soils.

«
...
5
6
7
8
9
...
»

Summary of Contents for Spirit R





















Reviews:

No comments

Related manuals for Spirit R

Brand: Raymarine Pages: 70

Brand: Harbor Freight Tools Pages: 4

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: QRS Pages: 16

Brand: QMAXZ Lighting Pages: 36

Brand: Zero88 Pages: 26

Brand: HAMOKI Pages: 7

Brand: H&S Pages: 56

Brand: Life Fitness Pages: 45

VADA TWIN MOTOR MACERATOR

Brand: Reece Pages: 7

Brand: VIVAKID Pages: 12

Brand: Pfeuffer Pages: 32

Brand: WATSON INDUSTRIES Pages: 17

Brand: Buki Pages: 16

Brand: Sentinel Pages: 4

Brand: PASCO Pages: 36

Brand: Grundfos Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands