background image

1011

2. Remove power head and place in an upside down position.

3. Install the cartridge filter over the filter cage with the flat end of the filter 

towards the vacuum cleaner power head.  Carefully push filter in until it 

stops against the power head.  (fig.2 & 3)

4. Place filter retainer on top of cartridge filter over the raise lip and tighten 

down by turning retainer clockwise, do not over tighten.  (fig. 4 & 5)

Removing and Cleaning Filter

1. Unlock and remove the filter retainer by tuning retainer handle counter 

clockwise.

2. Carefully hold and pull the cartridge filter up for removal.  (fig.6)

3. Clean the cartridge filter by gently tapping or brushing dirt off.  Cleaning 

should not be done indoors in living areas.   For optimal performance a 

new filter is recommended.  

4. Install cleaned or new filter into place as instructed above in steps 2 and 

3 of Installing Cartridge Filter.

5. Wet filters should be removed and allowed to air dry for 24 hours before 

installing onto the filter cage.

6. Carefully remove the pre-filter from the container and clean the dirt from 

the filter by gently tapping or brushing dirt off.

I

NSTALLING & CLEANING FOAM FILTER

Installing Foam Filter

1. Verify that the power cord is disconnected from the power socket. (fig.1)

2. Remove power head and place in an upside down position.  Follow 

instructions to remove cartridge filter.

3. Carefully slide foam filter down over the filter cage making sure the 

whole cage is covered. (fig.2 & 3)

4. Replace the power head on to the container.

Cleaning Foam Filter    

1. With the removed power head in the upside down position, carefully 

remove foam filter. (fig.4)

2. Use a mild soap and water solution to wash foam filter and rinse with 

clean water. (fig.5)

3. Allow filter to air dry before installing and using again.

T

ROUBLESHOOTING

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG 

BEFORE TROUBLESHOOTING.

Symptom

Possible Causes

Corrective Action

Vacuum 

cleaner will not 

operate.

1)  No power supply.

1)  Check power supply – 

cord, breakers, fuses.

2)  Faulty power cord.

2)  Unplug and check the 

power cord.  If damaged, 

have it repaired by a 

professional.

3)  Container full.

3)  Empty container.

Dust comes 

out from motor 

cover.

1)  The cartridge filter or 

dust bag is missing or 

damaged.

1)  Attach or replace 

cartridge filter or dust bag.

Reduced 

efficiency and 

motor/speed 

vibration.

1)  There is a blockage 

in the nozzle or hose, or 

the container inlet. Or 

dust filter blocked by fine 

dust.

1)  Check nozzle, hose 

and container inlets for 

blockage. Take off the filter 

and clean it. Or install new 

cartridge filter.

10

1

2

3

4

5

Summary of Contents for VQ1530SIWDC













Reviews: