V2 PD9, Manual, Page: 5 / 15

18
CONTROL PANEL
Per form the electrical connections to the terminal
board, then supply power to the system: the unit will
check the operation status of the display, by turning all
the segments on for 1,5 seconds (
8.8.8.8 ); after this,
the display will show the firmware version for 1,5
seconds, for instance
Pr 1.0 .
Now, the display will show a control panel:
The control panel represents the physical status of the
terminal board contacts and of the program mode keys:
if the upper ver tical segment is on, the contact is clo-
sed; if the lower ver tical segment is on, the contact is
open (the above picture shows an instance where the
inputs START, START P, PHOTO1, PHOTO2, and STOP
have all been correctly connected).
PROGRAMMING
The PD9 unit presents a programming structure with
menus, each of which corresponds to a function in the
unit (function menu) or to a working time setting (time
menu).
Time menus allow adjusting the unit working times
(e.g.: leaf opening or closing time, locking time, preflas-
hing time, etc.).
Time programming will be carried out through an algo-
rithm, which speeds up the operations by automatically
matching the adjustment pitch according to the current
set up value:
•
from 0 seconds to 1 minute the adjustment pitch is
equal to 0,5 second:
• from 1 minute to 10 minutes the adjustment pitch
is equal to 5 seconds:
• for more than 10 minutes the adjustment pitch is
equal to 30 seconds:
On the other side, the function menu are used to acti-
vate the required functions (e.g. timed lights, PHOTO1
active as a travelling edge, PHOTO2 inactive, etc.).
Some time menus depend on cer tain function menus
(e.g.: if the AUTOMATIC CLOSING is activated – but only
in this case – a TIME-OUT need to be set); then, to sim-
plify the programming, these time menus have been
placed in the function menus on which they depend.
Specifically, menus AUTOMATIC CLOSING (Ch.AU) and
PHOTOCELL TIME-OUT (Ft.PA) offer some “time menus”
among the selectable options.
FUNCTION OF KEYS
MENU, UP, DOWN
To activate the program mode, proceed as follows.
•
After powering the unit, the display should show the
control panel (therefore, check that the connections
made are correct).
• Press and hold key MENU until the display
shows
dEF .
Now your programming has been activated.
WARNING: in case no operation is carried out for more
than one minute, the gearcase exits from the program-
ming mode without saving any of your setups and chan-
ges, which will get lost.
You will have to exit from the programming mode –
through the
FinE menu – to store all set up data (even
in case you choose the default data).
When the program mode function is activated, press
key UP or DOWN to select the menus, thus per forming
a for ward or backward shift (for a fast shift, press and
hold).
Press key MENU to access the settings in order to
change them through keys UP and DOWN.
• Pressing the UP key, the menu functions can be
scrolled from below.
• Pressing the DOWN key, the menu functions can be
scrolled from above.
• Pressing the MENU key, the settings to be changed
can be accessed and selected by pressing again.
ATTENTION: when the program mode function is not
activated, pressing of the UP key corresponds to the
START command, pressing of the DOWN key corre-
sponds to the PEDESTRIAN START command: this way,
the ser vice engineer is enabled to per form the test and
the set-up.
The PD9 unit can be set up in two different program
modes: DEFAULT PROGRAM MODE or CUSTOM
PROGRAM MODE.
In the following pages you can find a functions diagram
with information concerning PD9.
For the use of the function char t proceed as follow:
• Press DOWN key to flow the char t from the top to
the bottom. The functions
dEF , t.AP1 , t.AP2 etc.
will be appear.