background image

E

N

G

L

IS

H

47

DISPLAY

DATA

FUNCTION

DEFAULT MEMO

CoS1

Safety ribbon 1 input

This menu allows enabling the input for type 1 safety ribbon, that is to say,
fixed ribbons

no

no

Input disabled (ignored by the control unit)

A P

Input enabled during the opening and disabled during the closure

A PCh

Input enabled in opening and closure

CoS2

Safety ribbon 2 input

This menu allows enabling the input for type 2 safety ribbon, that is to say
mobile ribbons

no

no

Input disabled (ignored by the control unit)

A PCh

Input enabled in opening and closure

Ch

Input enabled during closure and disabled during opening

Co.tE

Test of the safety edges

This menu allows setting the method of control of the safety edges working

no

no

Test disabled

rESi

Test enabled for conductive rubber safety edges

Foto

Test enabled for optical safety edges

S.EnC

Encoder sensitivity

0

0 - 7

This menu allows the sensitivity of the rate sensor to be adjusted.
A decreased rate below the set threshold indicates the presence of an
obstacle.
If set to 

0

the obstacle is only detected when the gate is stopped.

When the sensor intervenes, the gate stops and is operated in the reverse
direction for 3 seconds to remove the obstacle.
The next start command restarts the movement in the previous direction.

i.A di

Enabling the ADI device

This menu makes it possible to enable operation of the device
connected to the ADI connector.

PLEASE NOTE: 

selecting 

Si

and pressing MENU accesses the

configuration menu for the device connected to the ADI connector.
This menu is managed by the device itself and is different for each
device. Please refer to the manual for the device.
If the 

Si

option is selected, but no device is connected, the display will

show a series of dotted lines.
Exiting the ADI device configuration menu returns to the 

i.A di

option

no

no

Interface disabled, any signals will be ignored

Si

Interface enabled

FinE

End of Programming

This menu allows to finish the programming (both default and
personalized) saving the modified data into memory

no

no

Do not exit the programming menu

Si

Exit from the programming menu, storing the parameters set

Summary of Contents for ALFARISS






























Reviews: