UTICA BOILERS UBSSC-050 Installation, Operation & Maintenance Manual Download

Page: 31 / 88

Multiple

Family

Dwellings

Vent shall not terminate directly above paved

sidewalk or paved driveway located between

two single-family dwellings serving both

dwellings.

7' (2.1m)

Minimum

3' (914mm)

Minimum

Termination

Stones,

Balls, Etc.

Position combustion air and vent

termination where it will NOT be damaged by

foreign objects, such as stones, balls, etc.

People or

Pets

Locate combustion air and vent termination to

prevent accidental contact with people or pets.

Eddy, Flue

Gases

Position termination so it will not be effected

by wind eddy, air born leaves, snow, or

recirculated vent gases. Give consideration

to excessive wind and locate away from

windward side of building.

Vapors

Position termination where vent vapors are

not objectionable.

Walkways

Locate vent termination minimum 7'

(2.1m) above any public walkway, with

consideration to condensate.

Meters,

Regulators,

deck, porch

Vent termination US only - 4’ (1.2m),

Canada - 6' (1.9m) horizontally from, no

case above or below, electric meters, gas

meters, regulators, and relief equipment,

or under deck or porch.

Vegetation,

Plants &

Shrubs

Keep vent termination 3’ minimum

(914mm) away from vegetation. Position

termination where vent vapors will not

damage plants/shrubs or air conditioning

equipment.

FIGURE 6-18

FIGURE 6-19

6 - COMBUSTION AIR AND VENT PIPING

PN 240011320 Rev. G 10/01/2021]

Summary of Contents for UBSSC-050

























































































Search results

Summary of Contents for UBSSC-050

Reviews:

Related manuals for UBSSC-050

Brands by name

Popular brands

UTICA BOILERS UBSSC-050, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for UBSSC-050

Reviews:

Related manuals for UBSSC-050

Brands by name

Popular brands