UTICA BOILERS UBSSC-050 Installation, Operation & Maintenance Manual Download

Page: 76 / 88

1.5

User Menu

User Interface Display

Explanation

STANDBY

Boiler operates in standby mode until demand for Central Heat

(CH) or Domestic Hot Water (DHW) is detected.

User Menu (Press Menu botton on user interface to access User Menu)

User Menu

User Menu structure includes:

• ‘Boiler Status’ submenu– User can monitor general boiler

status parameters such as sensor temperatures and pump

operation.

• ‘Settings’ submenu – User can view CH , adjust DHW supply

water set points and also select control language.

• ‘Cascade Status’ submenu – Boiler set to function as part of

multiple boiler installation; submenu used to view runtime

parameters. See Multiple Boiler Manual. (This line is

not shown if boiler is not in cascade system).

iler Status

Supply Temperature set point displayed.
If boiler running in CH mode, CH set point displayed.
Note:

• While running in Outdoor Reset mode, this value may

change in proportion with the outdoor temperature.

• If the boiler is running in DHW mode, the DHW supply set

point is displayed.

Several boiler runtime parameters can be viewed while in ‘Boiler

Status’ submenu.
Operational status of pump system also shown.
Information available during all states of boiler operation.

Sensor values with troubleshooting tree used to diagnose

typical problems.

APPENDIX A - CONTROL MODULE

PN 240011320 Rev. G 10/01/2021]

Summary of Contents for UBSSC-050

























































































Search results

Summary of Contents for UBSSC-050

Reviews:

Related manuals for UBSSC-050

Brands by name

Popular brands

UTICA BOILERS UBSSC-050, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for UBSSC-050

Reviews:

Related manuals for UBSSC-050

Brands by name

Popular brands