UTICA BOILERS UBSSC-050 Page 14 Installation, Operation & Maintenance Manual Download | Manualshive

Page: 14 / 88

background image

14

5 - HYDRONIC PIPING

5.1 General

• Install piping in accordance with authority having

jurisdiction.

• Support system piping and safety relief valve discharge

piping. Boiler's internal piping and wall mount bracket

can be damaged if subjected to excessive weight.

• Size central heating pump (and domestic hot water

pump, if used) for system requirements only. Internal

heat exchanger pump compensates for pressure drop

through boiler internal piping and heat exchanger.

•

Thoroughly clean and flush system before connecting to

boiler.

• If oil is present in system water, use approved detergent

to wash system.

• Flush system to remove any solid objects such as metal

chips, fibers, or Teflon tape, etc.

5.2 Special Conditions

Note

• System piping exposed to freezing conditions: Use

inhibited propylene glycol solutions certified by fluid

manufacturer for use with closed water heating system.
Do not use automotive or ethylene glycol.

• Boiler installed above radiation level (or as required by

authority having jurisdiction). Integral low water cutoff

provided in boiler. See pages 10 & 11.

• Boiler used in connection with refrigeration system.

Install piping in parallel with boiler, with appropriate
valves to prevent chilled medium from entering boiler.

• System piping connected to heating coils located in air

handling unit exposed to refrigerated air circulation.

Install flow control valves or other automatic means to

prevent gravity circulation of boiler water during cooling
cycle.

FIGURE 5-1 Safety Relief Valve & Air Vent

(Viewed

from front of boiler)

Safety Relief

Safety Relief

Valve

Valve

3/4" x 4 NPT

3/4" x 4 NPT

Nipple

Nipple

3/4" x 1/4"

3/4" x 1/4"

NPT 90°

NPT 90°

Elbow

Elbow

3/4"F x M x

3/4"F x M x

F NPT Tee

F NPT Tee

Air Vent

Air Vent

Note

Boiler rated at 150 psig (1.03 MPa) maximum
allowable working pressure. Boiler provided with
30 psig (206 kPa) safety relief valve. Field source
safety relief valve for system pressures greater
than 25 psig. Temperature Pressure Gauge
satisfactory for 60 psig operation. Field source
temperature pressure gauge for system pressures
greater than 60 psig.

Note

Position Air Vent and Safety Relief Valve to provide

space for discharge piping.

WARNING

• Poison hazard. Ethylene glycol is toxic. Do not

use ethylene glycol.

• Never use automotive or standard glycol

antifreeze, even ethylene glycol made for

hydronic systems.

• Ethylene glycol can attack gaskets and seals used

in hydronic systems.

• Use only inhibited propylene glycol solutions

certified by fluid manufacturer as acceptable for

use with closed water heating system.

•

Thoroughly clean and flush any system that used

glycol before installing new Boiler.

• Provide user with Material Safety Data Sheet

(MSDS) on fluid used.

!

Do not expose boiler and condensate piping to

freezing temperatures.

PN 240011320 Rev. G 10/01/2021]

«
...
12
13
14
15
16
...
»

Summary of Contents for UBSSC-050

























































































Reviews:

No comments

Related manuals for UBSSC-050

Purewell VariHeat 70c

Brand: Hamworthy Pages: 72

Brand: STIEBEL ELTRON Pages: 60

Brand: Buderus Pages: 2

Brand: Sime Pages: 40

Brand: OSO HOTWATER Pages: 48

Brand: E.C.A. Pages: 48

Classic FF 3 100

Brand: Ideal Boilers Pages: 40

Brand: ACV Pages: 8

Brand: ACV Pages: 28

Brand: Electric Heating Company Pages: 20

Brand: Alternate Heating Pages: 66

Vitogas 050 ECD Series

Brand: Viessmann Pages: 28

BAYKAN 24kW Sun Premix

Brand: GasTech Pages: 20

Brand: Unical Pages: 36

04061 Hydroboil

Brand: Zip Pages: 12

Brand: UTICA BOILERS Pages: 28

Brand: Ferroli Pages: 13

Brand: UTICA BOILERS Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands