background image

41

 

ISS Sensor Signal Plausibility Error 

The controller detected an unexpected value from this sensor and marked it as 
faulty. (if equipped) 

 

Checksum error in table (Can be table 1-4)

 

A Checksum error has been found in the table corresponding to the number 
shown. On Quick 6, this error will force a hard failsafe mode until it is fixed. It will 
also disable the tuning menu for the bad table. Connect the controller to a PC 
and load a calibration using Shiftware. 
 

Torque Converter Clutch Slip Error 

Torque converter clutch slip detected when fully engaged. 
 

Transmission Slip in Gear(s) 1, 2, 3, etc. 

Transmission appears to be slipping in the indicated gear or gears. 
 

Transmission Slip with Max Pressure 

Transmission continued to slip after maximum line pressure was commanded. 
 

Transmission Slip Repeated > 2x 

Transmission slip was detected more than twice in this drive cycle (max. line 
pressure latched). 
 

Ratio too High in Gear(s) 2, 3, 4, etc. 

Transmission gear ratio appears to be too high in the indicated gear or gears. 
 

Error: PRNDL Out of Range 

Sensor voltage is out of tolerance limits, but within approximate range. 
 

Error: PRNDL Signal Low 

Sensor voltage is low. 
 

Error: PRNDL Signal High 

Sensor voltage is high. 
 

Error: No PRNDL PWM Signal

 

Connect the controller to a PC and use Shiftware to reload the calibration using 
a E4OD calibration. 
 

Summary of Contents for Quick4 4R100













































Reviews: