US Shift Quick4 4R100 Installation And Operation Manual Download Page 4 | Manualshive

Page: 4 / 44

background image

4

PREPARATION

Pre-1995 Transmissions

The Quick 4 does not support the early ATR (MLPS or Range Sensor)
connector used from 1989 to 1994. It was found to not be adequately
waterproof. Ford services the old sensor by providing the new one with the
updated connector shell and instructions for replacing it. If you don’t already
have the 1995 and up range senor, you will need to purchase it. US Shift sells
the updated range sensor as well as Ford.

«
...
2
3
4
5
6
...
»

Summary of Contents for Quick4 4R100













































Reviews:

No comments

Related manuals for Quick4 4R100

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 600

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 30

EASA-PHONE KX-T61610

Brand: Panasonic Pages: 4

EASA-PHONE KX-T30850

Brand: Panasonic Pages: 6

Brand: JBL Pages: 16

Authentics L 16

Brand: JBL Pages: 17

Brand: KAM Pages: 4

Brand: Fame Audio Pages: 9

Brand: Senal Pages: 12

Brand: Vectra Fitness Pages: 4

Brand: Bigben Pages: 64

Brand: Sennheiser Pages: 29

Brand: Aeromic Pages: 2

Brand: Kenwood Pages: 40

Brand: Kenwood Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands