URAL Motorcycles 2014 Gear up Owner'S Manual Download

Page: 55 / 99

The front disc brakes require periodic inspection, but do not require adjustment. The brake pads

can be inspected by removing the dust shield from the top of the caliper and checking the thick-

ness of the pads. The pads should be replaced when less the 1/8 inch of pad is remaining on

either pad. The brake hose should be inspected periodically for leaks and cracks along the length

of the hose as well as the banjo fittings on either end.

WARNING:

Never use

any aftermarket brake hose for the front brake. Use only genuine Ural

brake hoses, failure to do so could result in front brake failure and voiding the warranty.

The front disc brakes require periodic inspection, but do not require adjustment. The brake

pads can be inspected by removing the dust shield from the top of the caliper and checking

the thickness of the pads. The pads should be replaced when less the 1/8 inch of pad is

remaining on either pad. The brake hose should be inspected periodically for leaks and

cracks along the length of the hose as well as the banjo fittings on either end.

WARNING: Never use

any aftermarket brake hose for the front brake. Use only genuine Ural

brake hoses, failure to do so could result in front brake failure and voiding the warranty.

Summary of Contents for 2014 Gear up




































































































Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands

URAL Motorcycles 2014 Gear up, Owner'S Manual

Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands