URAL Motorcycles 2014 Gear up Owner'S Manual Download

Page: 20 / 99

Parking Brake Sidecar Drive Lever Reverse Gear Lever

Rear Brake Pedal

Parking Brake

is used to hold the bike when parked. To engage, depress the rear brake pedal

and push down then twist the parking brake lever counter clockwise.

Sidecar drive engagement lever

is used to engage the drive axle to the sidecar wheel on the

Patrol and Gear Up model motorcycles.

WARNING:

ever engage sidecar drive on concrete or hard surface.

evere damage to

drivetrain will result if the sidecar drive is engaged on pavement.

Reverse gear lever

is used to move the motorcycle in reverse. The transmission must be in

neutral or 1st gear for reverse gear to be engaged.

Rear brake lever

is used to actuate the rear brakes.

WARNING: D

NOT

APPLY

EITHER

BRAKE

STRONGLY

ENOUGH

LOCK

THE

WHEELS

BECAUSE

THIS

MAY

CAUSE

POSSIBLE

LOSS

CONTROL

THE

MOTORCYCLE

. A

LWAYS

USE

BOTH

BRAKES

. N

EVER

STOP

WITH

FRONT

REAR

BRAKE

ONLY

WARNING: A

IMPROPERLY

ADJUSTED

REAR

BRAKE

PEDAL

COULD

INTERFERE

WITH

PROPER

REAR

BRAKE

OPERATION

RESULTING

POOR

BRAKE

ACTION

Summary of Contents for 2014 Gear up




































































































Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands

URAL Motorcycles 2014 Gear up, Owner'S Manual

Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands