URAL Motorcycles 2014 Gear up Owner'S Manual Download | Manualshive

Page: 40 / 99

background image

40

CARBURETOR MAINTENANCE

The carburetors will require the fuel in the float bowls be drained periodically. This will ensure that
any contaminants that have accumulated in the float bowls do not enter the main or idle jets of the
carburetors. The fuel can be drained by opening the drains provided on the bottom of the float
bowls.

The fuel filters should also be changed every 10,000 km or when they appear to be dirty or
blocking fuel. Changing the filters will ensure that clean fuel is provided to the carburetors and that
there is no fuel starvation.

The carburetor to cylinder head adapters should be checked for leaks and cracks every trip.
Failure of the adapters will cause the carburetor fuel mixture to become lean and cause internal
damage to the engine.

«
...
38
39
40
41
42
...
»

Summary of Contents for 2014 Gear up




































































































Reviews:

No comments

Related manuals for 2014 Gear up

Brand: ACERBIS Pages: 72

Brand: hepco & becker Pages: 5

Brand: KEEWAY Pages: 15

Brand: Honda Pages: 100

Rebellion Electric Chopper 15130760

Brand: Razor Pages: 17

SoundBomb TT-SB.10100.B

Brand: Denali Pages: 3

Brand: zeeltronic Pages: 10

Brand: Yamaha Pages: 338

Brand: SCHUBERTH Pages: 43

Brand: Sundstrom Pages: 68

Brand: Arai Pages: 12

Brand: Britannia Pages: 9

Brand: R&G Pages: 23

DORSODURO 1200 ABS - ATC

Brand: APRILIA Pages: 408

Brand: hepco & becker Pages: 4

Brand: Race Dynamics Pages: 20

Goldwing GL1200

Brand: Honda Pages: 32

Goldwing GL1100 Aspencade 1982

Brand: Honda Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands