URAL Motorcycles 2014 Gear up Owner'S Manual Download

Page: 24 / 99

Throttle Control

is on the right handlebar. Turning the twist grip increases engine speed.

Ignition Cutoff Switch

has two positions, ignition off (up), and ignition on (down).

Electric Start Button

is located on the right-hand twist grip, below the kill switch.

Low and High Beam Light

Switch

has two positions, high beam (up), and low beam (down).

Turn indicator switch

is used for signaling a turn

Horn

push-button

is used to activate the horn

Steering Damper

absorbs lateral kicks to the front wheel. Turning tightening bolt (clockwise in-

creases friction. This can be used while riding over bad roads.

TEERING

AMPER

DJUSTMENT

NOB

WARNING: D

NOT

TIGHTEN

THE

DAMPER

THE

POINT

WHERE

THE

STEERING

BECOMES

STIFF

. D

OING

WILL

ADVERSELY

AFFECT

HANDLING

QUALITIES

AND

MAY

DAMAGE

THE

STEERING

MECHANISM

Parking brake

is located on the right side of the motorcycle next to the foot peg. It is engaged by

applying the foot brake pedal fully and turning the handle and pushing it down to hold the foot brake
lever in the applied position.

Always disengage the parking brake before moving the motorcycle.

Summary of Contents for 2014 Gear up




































































































Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands

URAL Motorcycles 2014 Gear up, Owner'S Manual

Search results

Summary of Contents for 2014 Gear up

Reviews:

Related manuals for 2014 Gear up

Brands by name

Popular brands