background image

www.uponor-usa.com • www.uponor.ca

28

Uponor Climate Co˘ntrol™ Zoning System Installation Guide

29

Information Menu

The Information menu provides information about rooms, 
alarms/error messages and settings.

Information Menu: Room Information

1.   Uponor screen 

>

 Main Menu 

>

 Information 

>

 Rooms

2.   

>

 Select the desired room. 

>

 Press OK.

The number at the beginning of the room name 
on the display means: First digit: base unit. 
Second and third digits: number of the first 
channel controlled by this thermostat  
(01, 02, 03, etc.). If several terminals are 
controlled by the thermostat, only the lowest 
terminal number is displayed.

Room Temperature 

When room 
information is 
accessed, the screen displays room 
setpoint and measured temperature.  
The temperature setpoint is 69.8°F.  
If the temperature set on the thermostat 
is outside the allowed temperature range 
for the room, the limitation temperature 
will be displayed as setpoint.

The measured temperature is 70.16°F.

3.   

>

   to open the next screen.

ECO (Economy)

This screen displays 
the temperature  
setting for the room when it is in ECO 
mode. (Current setting is 66.2°F.)

Current status: 
COMF: Comfort mode. 
ECO: Economy mode

4.   

>

   to open the next screen

Battery and Communication Status

Battery and communication status are indicated  
with a √ or X.

•  Battery: The batteries are  

sufficiently charged.

•  Signal: Radio signal from the 

thermostat  
is good.

•  Battery: The batteries are low.

•  Signal: Radio signal from the 

thermostat and the antenna is faulty.

Thermostat and Actuator Status

Yes:  The thermostat is calling for heat.

No:  The thermostat is reporting that the 

room temperature is satisfied.

Open:  The actuators 

are powered 
and open or opening.

Closed:  There is no power to the 

actuators and they are closed  
or closing.

The minimum temperature setpoint of 
the room is set at 53.6°F.

The maximum temperature setpoint of 
the room is set at 78.8°F.

Actuator Status

This screen is only displayed during installation.

 

OK:  Normal  

operation

Alarm:  A short circuit or similar problem 

is reported.

Alarms
System

Rooms

Information

1.07 Gym

1.02 Living

Room List

Battery

1.02 Living

More

Signal

Measured

Set Point

1.02 Living

More

69.8˚F

70.16˚F

StatCall:  No Act.:  Closed

1.02 Living

More

Min: 53.6˚F  Max: 78.80

Status

ECO Temp

1.02 Living

More

66.2˚F

COMF

Status

Statcall

Act.

Min

Max

Interface Screens

Uponor Screen

• Pressing any button activates backlighting.
• To go to the main menu, press OK.

Uponor Screen Icons

Vacation mode is activated.

An alarm/error message is present.

The outdoor temperature is displayed if the system is 
fitted with an outdoor temperature sensor.

The Interface menu displays indoor temperature; it will 
also display outdoor temperature if the system is fitted 
with an outdoor temperature sensor.

Main Menu

1. Upper banner: Menu heading
2. Information zone: The selected line is highlighted.
3. Scroll bar

How to Access and Navigate the Menu

Uponor

14  Jun  2008       2 : 00

1. 

>

 Press OK.

Vacation Mode
Settings

Information

Main Menu

2. 

>

 Information 

>

 Press OK.

Alarms
System

Rooms

Information

3. 

>

 Rooms 

>

 Press OK.

1.07 Gym

1.02 Living

Room List

4.  

>

 Select the desired room. 

>

 Press OK.

•  Display the desired information using the navigation 

keys. Use   and   to display the previous/next 
screen. Use   and   to display the previous/next 
thermostat.

•  To go back to the room list, press OK.

Access Level

This parameter allows the user to set or select the  
access level. Two levels are available: basic or advanced.

The basic level allows the user to view some 
basic information, but not modify the settings. 
Recommended for use in a public location or a 
rented accommodation, such as a hotel room. 
The advanced level allows users to  
modify settings.

1.  

>

 Uponor screen 

>

 Main Menu 

>

 Settings 

>

 System 

Parameters 

>

 Access Level selection

Advanced

Basic

Access Level

2.   

>

 Basic or Advanced  

>

 Press OK.

To switch from Basic to Advanced Level:  
On the Uponor screen, simultaneously press   
and   for 10 seconds.

Screen Advanced and OK appears. Press OK to put the 
system is in Advanced mode.

Uponor

14  Jun  2008       2 : 00

Uponor

10  Nov  2008       5 : 19

Outdoor  32

¡

F

Uponor

20  Nov  2008       5 : 19

Outdoor  32

°

F

Indoor Average  70.16

°

F

Vacation Mode
Settings

2

3

1

Information

Main Menu

Actuator:  Alarm

1.02 Living

More

Actuator

Summary of Contents for C-55
































Reviews: