Uplift Desk FRM300 Instructions Manual Download Page 2

© UPLIFT Desk

 • 1-800-349-3839 • 1-512-614-3152 • [email protected] • upliftdesk.com

2

When using an electrical furnishing, basic precautions should always be followed, including the following: 
Read all instructions before using the desk.

FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS 
AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAM-
AGE OR BODILY INJURY.
DANGER - 

To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet be-

fore moving, cleaning, or before adding or removing parts and accessories. 

SAFETY AND WARNINGS

WARNING - 

To reduce the risk of burns, fire, electric shock, injury to persons, or property damage:

•  Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled 

persons. Children should only use the desk under adult supervision. Keep children away from electric 

height adjustable desks, control units, and keypads. There is a risk of injury and electric shock.

•  Use this desk only for its intended use as described in these instructions. Do not use attachments not 

recommended by the manufacturer.

•  Keep the desk close to the power outlet to be easily accessible.
•  Never operate this desk if it has a damaged cord or plug, if it is not working properly, has been 

dropped or damaged.

•  Keep the cords away from heated surfaces.
•  Do not open any of the components: legs, control box, or keypad. There is a danger of electric shock. 

Do not insert anything into any seam or opening.

•  Keep all electrical components away from liquids.
•  Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
•  Do not use outdoors.

•  Inappropriate use of this product may cause property or bodily injury.

•  Check surroundings on all sides before using the desk to ensure there are no areas of interference 

between an immobile obstacle and the desk’s range of motion.

•  Ensure the length of power cords are of appropriate length for desk travel. Monitors, computers, 

speakers, and anything with a cord that is not long enough for the desk’s range of motion could be 

pulled off the desk, cause other items to fall, and could damage personal property or cause injury.

•  Please provide this manual to any users, installers, or support personnel operating the product.
•  If casters are not installed, employ two people to lift the desk so that it can be moved without 

dragging. Dragging the desk may cause the frame and screws to come loose from the desktop.

•  Maximum Lifting capacity of this product is 530 Ib. Do not overload your desk.
•  

Keep hands and fingers clear of moving parts.

This height adjustable desk has an electric motor and is designed for use in dry work areas only. The desk 
height is adjustable so that it can be positioned at the most ergonomically suitable height. These desks are 

designed only for the purposes included in this manual. They should not be used in environments with high 
humidity or dampness. Any other use is at user’s risk.

Do not sit or stand on the desk frame.

Children should never use the desk unless they are supervised by adults.

Liability: 

Under no circumstances does the manufacturer accept warranty claims or liability claims for dam-

ages caused from improper use or handling of the desk frame other than that which is described in this 
operation manual.

USAGE

Summary of Contents for FRM300

















Reviews: