Unimac AIRSAWUMCAH16 User Manual Download Page 9

Page: 9 / 12

AIR METAL SAW

Maintenance

Tool Use and Care

1. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the

work by hand or against the body is unstable and is able to lead to loss of control.

2. Do not exceed the maximum 16 gauge thickness when cutting sheet metal with saw.

3. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer

at the rate for which the tool is designed.

4. Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

5. Disconnect the tool from the air source before making any adjustments, changing accessories, or storing the

tool. Such preventive safety measures reduce the risk of starting the tool unintentionally. Turn off and detach
the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its
off position before leaving the work area.

6. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the

hands of untrained users.

7. Maintain the tool with care. Keep a cutting tool sharp and clean. A properly maintained tool, with sharp

cutting edges reduces the risk of binding and is easier to control.

8. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects

the tool's operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly
maintained tools. There is a risk of bursting if the tool is damaged.

9. Use only accessories that are identified by the manufacturer for the specific tool model. Use of an accessory

not intended for use with the specific tool model, increases the risk of injury to persons.

Cleaning, Maintenance, and Lubrication

NOTE:

These procedures are in addition to the regular checks and maintenance explained as part of the regular

operation of the air-operated tool.

1. Daily - Air Supply Maintenance:

Every day, maintain the air supply according to the component manufacturers' instructions. Maintain the
lubricator's oil level. Drain the moisture filter regularly. Performing routine air supply maintenance will allow
the tool to operate more safely and will also reduce wear on the tool.

2. Make sure that the Housing that holds the blades and Air Inlet are free of dirt and debris.

3. Periodically: Apply a light machine oil to the pivot point on the Throttle.

4. Before Each Use: Check to make sure blades and Blade Guard are securely in place. If necessary, tighten

the Set Screws.

5. Quarterly (every 3 months) – Tool Disassembly, Cleaning, and Inspection:

Have the internal mechanism cleaned, inspected, and lubricated by a qualified technician.

Troubleshooting

PROBLEM

POSSIBLE CAUSE

LIKELY SOLUTIONS

Decreased output

Not enough air pressure and/or air
flow

Check for loose c connections and make sure that air supply
is providing enough air flow (CFM) at required pressure
(PSI) to the tool's air inlet.

Do not exceed maximum air

pressure.

Obstructed Throttle

Clean around Throttle to ensure free movement

Incorrect lubrication or not enough

Lubricate using air tool oil and grease according to directions

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC