background image

 

 

GENERAL NOTES 

 

1.1

 

PERMITTED USE 

The touch screen remote control panel allows the centralized management of a network of chiller/heat pump. It can also be used 

for partial functions (i.e. as a remote control panel of a single chiller/heat pump or ambient temperature thermostat). 

It includes humidity and temperature sensors for the thermo hygrometric analysis of the environment and for the management of 

the double set point for radiant floor heating systems that use a dehumidification system. 

The intuitive interface simplifies the use of the control;  all the functions  can be  easily  set through the use of immediate 

understanding synoptic. 

The remote control supervises and periodically examises the network, there is a cycle time that elapses between the signaling or 

command request and the activation of the function, the cycle time depends on the largeness of a network of fancoils and heat 

pumps. 

For multi-circuit units only the I/O ports and parameters of the first circuit can be displayed. 

1.2

 

USE NOT PERMITTED 

Any use different than that permitted is PROHIBITED. 

1.3

 

TECHNICAL DATA 

Features 

Nominal 

Min. 

Max. 

Power supply voltage 

12Vac 

10Vac 

14Vac 

Power supply frequency 

50 - 60Hz 

Tip-5% 

Tip+5% 

Operating ambient temperature 

25°C 

0°C 

50°C 

Operating humidity (non-condensing) 

30% 

10% 

90% 

Ambient storage temperature 

25°C 

-20°C 

70°C 

Ambient storage humidity (non-condensing) 

30% 

10% 

90% 

Class of device (according to EU REG 2013-811) 

Contribution of temperature control to the seasonal energy efficiency of heating 

environment. (according to EU REG 2013-811) 

2% 

1.4

 

ELECTROMECHANICS CHARACTERISTICS 

Terminals and connectors 

Screw terminals 

Analogue inputs 

1 NTC sensor on board 

1 humidity sensor on board 

Serial 

1 USB Host (for mass storage plug) 

1 Isolated RS485 network for chiller/heat pump and fancoils 

1 TTL serial port for future uses (optional plug-ins) 

1 Ethernet port 

Transformer 

Device not included 

Watch 

RTC watch with backup condenser 

Display 

LCD TFT 4.3” 480x272 pixels 

Keys 

Resistive touch screen mounted on the LCD 

Dimensions 

128x81.2mm depth 35mm (box) 

Case 

Is made up of white plastic 

 

Summary of Contents for TOUCH SCREEN N













































Reviews: