Unical TERNOx 2S Instructions On Installation, Use And Maintenance Download

Page: 41 / 48

Tec

hnical f

eatures and dimensions

Have all the hydraulic and electrical systems and the safety devices and fuel been connected in compliance
with the domestic and local laws in force?

Are the expansion vessel and the safety valve (when applicable) connected correctly and cannot be shut off?

Are the bulbs of the operating, safety, minimum thermostats and that of the thermometer inserted in their
conduits?

Are the control and safety devices working and configured correctly?

Are the refractory coverings intact?

Are the combustion air intake line and the flue gas evacuation line compliant with the applicable standards in
force?

does the gas used (models with gas burner) correspond to boiler calibration?

is the fuel supply system sized according to the capacity required by the boiler?

is it equipped with all safety and control devices required by the standards in force?

are the mains voltage and frequency compatible with the burner and the electrical equipment of the boiler?

is the burner assembled according to the instructions in the manufacturer's manual?

has the burner blast tube infill been performed correctly?

Is the system full of water and does not contain any air?

Are the drain valves closed and the system cut-off devices fully open?

is the gas supply cock open (models with gas burner)?

has gas leakage been checked (models with gas burner)?

Is the outside main switch ON?

Is the pump/are the pumps working correctly?

has the system been checked for water leaks?

Are the ventilation conditions and minimum distances to perform any maintenance guaranteed?

Has the operator been trained and has the documentation been supplied?

3.22 - COMMISSIONING

3.22.1 - Preliminary checks

Commissioning must be done by profession-
ally qualified personnel. Unical will not be
held liable for damage to persons, animals
or objects due to failure to comply with the
above instruction.

Please tick the operations performed

After connecting the hydraulic and electrical system and the fuel line to the boiler, and before starting up the boiler,

it is advisable

to check the following:

Summary of Contents for TERNOx 2S

















































Search results

Summary of Contents for TERNOx 2S

Reviews:

Related manuals for TERNOx 2S

Brands by name

Popular brands

Unical TERNOx 2S, Instructions On Installation, Use And Maintenance

Search results

Summary of Contents for TERNOx 2S

Reviews:

Related manuals for TERNOx 2S

Brands by name

Popular brands