Unical HP OWER 320RK, User'S And Installer'S Manual

Page: 73 / 88

32
Danger Indication / Instruction Residual risk
User / Activity
Operator User
Tra
ns
po
rt
p
ha
se
In
sta
lla
tio
n
ph
as
e
M
ai
nte
na
nc
e
ph
as
e
Un
it
in
te
ra
cti
on
No
rma
l u
ni
t o
per
at
io
n
Generated by materials / sub-
stances: fire / explosion causes
gas classified as slightly flamma-
ble
The user-installer manual under
chapter 5 contains specific indica-
tions about unit installation place
and protection devices.
Failure to comply with the
indications relating to the place
of installation and adequate
maintenance procedures.
X X
Generated by materials / sub-
stances: infections caused by
bacteria potentially present in the
carrier fluid (technical water)
The permitted uses of the unit
are listed in the user-installer
manual under chapter 3.
Failure to comply with the in-
structions given in the manual.
X X
Generated by materials /
substances: burn caused by the
presence of oil inside the refriger-
ation circuit, triggered by a flame
welding torch
The use of personal protective
equipment is recommended in
the user-installer manual under
paragraph 4.2.
Under chapter 9 it is advisable,
in the case of maintenance that
involves desoldering the tubes, to
proceed with cutting them, as the
flame of the torch for desoldering
triggers any oil present.
Failure to comply with the in-
structions given in the manual.
X
Generated by materials /
substances: burn / scald from
escaping refrigerant
The safety measures to be adopt-
ed in case of maintenance, clean-
ing or control of the unit and the
personal protective equipment
to be equipped are indicated in
the user-installer manual under
chapter 9.
Failure to comply with the in-
structions given in the manual.
X X
Generated by materials /
substances: pollution due to inap-
propriate disposal
The instructions for correct dis-
posal are given in the user-install-
er manual under chapter 10.
Failure to comply with the in-
structions given in the manual.
Ergonomic: fatigue / musculoskel-
etal disorders caused by exertion
during maintenance / installation
Under paragraph 4.1, the us-
er-installer manual recommends
compliance with current regu-
lations (international and local)
regarding workers health and
safety. During maintenance, it is
advisable to keep a posture that
does not cause fatigue and to
check the weight of the compo-
nent before proceeding with its
handling (paragraph 9.3).
Failure to comply with the in-
structions given in the manual.
X X
Generated by unit use environ-
ment: Slipping / falling caused by
ice / water near the unit due to
condensate drain / defrost
Under paragraph 5.8.5 the
user-installer manual indicates
about condensate drain system,
recommending that you pay at-
tention to the danger of slipping.
Failure to comply with the in-
structions given in the manual.
X X
Generated by unit use environ-
ment: unexpected events as a
result of malfunctions due to
water / snow / humidity.
In the user-installer manual un-
der chapter 9 it is recommended
to pay attention to the correct
tightening of the cable gland
designed for the passage of the
electric power cable and to the
reassembly of all the sheets, in
particular those of the electrical
panel, in order to maintain the
degree of declared protection.
Failure to comply with the
procedures by the maintenance
technician.
X X
Generated by unit use environ-
ment: lightning that can poten-
tially hit the unit
In the user-installer manual un-
der chapter 9 it is recommended
to carry out maintenance only in
weather conditions suitable for
the operations envisaged. It is
also indicated that the installation
site must be sufficiently far from
lightning rods or objects that
could attract the lightning (par.
5.3). The unit must be electri-
cally connected to a system that
complies with the regulations in
force.
Failure to comply with the in-
structions given in the manual.
X X