background image

 

4

 / 

14

 

 

 

AC 

Alternating current of device. Please check the region’s voltage range. 

 

DC 

Direct current 

of device. Please check the region’s voltage range. 

 

 

Grounding 

Frame and chassis grounding terminal. 

 

Grounding 

Protective grounding terminal. 

 

Grounding 

Measuring grounding terminal. 

 

OFF 

Main power off. 

 

ON 

Main power on. 

 

Power 

Supply 

Standby power supply: when the power switch is turned off, this device is not 

completely disconnected from the AC power supply. 

CAT I 

Secondary electrical circuit connected to wall sockets through transformers or similar 

equipment, such as electronic instruments and electronic equipment; electronic 

equipment with protective measures, and any high-voltage and low-voltage circuits, 

such as the copier in the office. 

CAT II 

CATII: Primary electrical circuit of the electrical equipment connected to the indoor 

socket via the power cord, such as mobile tools, home appliances, etc. Household 

appliances, portable tools (e.g. electric drill), household sockets, sockets more than 

10 meters away from CAT III circuit or sockets more than 20 meters away from CAT 

IV circuit. 

CAT III 

Primary circuit of large equipment directly connected to the distribution board and 

circuit between the distribution board and the socket (three-phase distributor circuit 

includes a single commercial lighting circuit). Fixed equipment, such as multi-phase 

motor and multi-phase fuse box; lighting equipment and lines inside large buildings; 

machine tools and power distribution boards at industrial sites (workshops). 

CAT IV 

Three-phase public power unit and outdoor power supply line equipment. Equipment 

designed to “initial connection”, such as power distribution system of power station, 

power instrument, front-end overload protection, and any outdoor transmission line 

 

Certification 

CE indicates a registered trademark of EU. 

 

Certification 

UKCA indicates a registered trademark of United Kingdom. 

 

Certification 

ETL indicates a registered trademark of Intertek. 

 

Waste 

This product complies with the marking requirements of WEEE Directive 

(2002/96/EC). This additional label indicates that this electrical / electronic product 

must not be discarded in household waste. 

 

EFUP 

This environment-friendly use period (EFUP) mark indicates that dangerous or toxic 

substances will not leak or cause damage within this indicated time period. The 

Summary of Contents for UPO1000CS Series















Reviews: