background image

 

 

ULVAC CRYOGENICS INCORPORATED   

7

 

3.2  Component Details 

 

Air inlet 

Port to intake the atmosphere. 

 

Maintenance port 

An opening to perform maintenance.    Make sure to turn off the power supply before 

opening this port.   

 

Ventilation fan 

Do not block the air exit by placing the fan too close to walls or in other ways. 

Take space of more than 200mm from walls. 

 

Cable entrance 

Entrance for power cables 

 

Nitrogen gas discharge port (

φ

6 easy connecting) 

 

Spare entrance port (Rc1/4) 

 

Pressure alarm light 

Illuminates when the pressure of nitrogen tank is below the set value. 

 

Nitrogen gas flow meter 

Displays the flow rate of nitrogen gas 

 

Compressor alarm light 

[Conditions that alarm light turns on] 

(1) When an overcurrent by reasons such as overloading of the compressor unit is 

detected 

(2) When the compressor wiring has any disconnection. 

 

Alarm light / Reset button 

When the compressor has some trouble, light turns on and the system stops 

operation.    The condition is reset by pressing the button again. 

 

Start / Stop button, light 

Press this button to start or stop the equipment.. The light is turned on during 

Summary of Contents for GN-15i

































Reviews: