background image

MOBUS 

10

 

 

MAINTENANCE

 

Ordinary 

At regular periods of time, depending on the usage of the product MOBUS: 
Turn the regulating knob at maximum and minimum level to check if working properly. 
Pay particular attention to verify that there is no water leakage checking the visible and exposed MOBUS parts. If at least 
one of the above controls fails, refer to Dangerous condition and risks section. 

Extraordinary 

We recommend the replacement of MOBUS (into the specific towel rail) every 5 years. 

 

CLEANING

 

To clean MOBUS, use only a dry and clean soft cloth. 
Make small locally round movements. 
Apply a light pressure especially to the chrome plastic surfaces to avoid potential scratches. 

 

DIAGNOSTIC

 

If the MOBUS regulation mode is selected at maximum temperature and the towel rail doesn’t heat at all, this may indicates 
operation failure and the product must be replaced. 
If LED is ON but the towel rail doesn’t heat, waiting 2 hours. If the situation doesn’t change, contact the customer service. 

 

SPARE PARTS

 

MOBUS must be replaced totally as it has no spare parts. 
 

IMPORTANT: In case of doubts, please, contact the Seller or refer to Contacts section.  
IMPORTANT: Please, retain these instructions for future reference 

 

NOTES FOR DISPOSAL OF THIS PRODUCT VALID FOR THE EUROPEAN UNION

 

 

The crossed-out wheeled-bin symbol on your product reminds you that in the European Union all electrical and electronic 

products and batteries must be taken to separate collection at the end of their working life. Do not dispose of these 

products as unsorted municipal waste. Return the products to collection to prevent possible harm to the environment or 

human health from uncontrolled waste disposal and to promote the sustainable reuse of material resources. Collection 
information is available from the product retailer, local waste authorities or national producer responsibility organizations. 

For more information, see product country-specific information. 

 
 

The manufacturer declines all responsibility for any inaccuracies in this document due to printing or transcription errors. It 
reserves the right to make any alterations to its products deemed necessary or useful. This document or any part of it 
cannot be copied, edited or reproduced without written authorization from the manufacturer. 

Summary of Contents for MOBUS














Reviews: