background image

1

)

 If the ignition key is On and a door is opened the Car Jack Mode Timer will start. 

    The siren will chirp one every second for 10 seconds then trigger into full alarm. 
                          

2)

 If the timer was activated by accident, within 10 seconds turn the ignition key back to On 

    then press and release the program button one time. The Car Jack Mode Timer will stop.  

3)

 If the timer is not deactivated Car Jack Mode will trigger into full alarm.  

    To deactivate turn the ignition On, then press and release the program button 5 times\
    then press unlock on the remote transmitter.

Emergency Override.

If Car Jack Mode is not deactivated in time, the system will need to be placed into 
Emergency Override. Turn the ignition key to the On position then press and hold 
the program button for 20seconds. At this time the customer can bring the vehicle 
back to the dealer for a system reset.
  

Car Jack

Diagnostics

While the system is disarmed and the ignition is in the off position, the LEDs 
will activate from the following triggers.
1)

 If the door is opened the LEDs will stay on until the door is closed.

2) 

If the hood is opened the LEDs will stay on until the hood is closed.

3)

 If the shock sensor detects vibration the LEDs will turn on momentarily.

4)

 If the auxiliary sensor input is activated the LEDs will activate momentary. 

 

If the alarm system is triggered while armed, the system will retain in memory the cause of the trigger. The diagnostics can 
then be used to determine what the cause of the trigger was. When disarming the alarm, the siren/horn will chirp 3 times
 instead of the usual 2 times to indicate the alarm had been triggered. The system’s LED will also flash in pulses to indicate 
which input triggered the alarm.

NOTE

: LED status will be cleared when ignition is turned ON.  For proper memory clearing, insure to connect the ignition

 input to the 

ignition 

on the vehicle.

Diagnostics Chart

  

Additional LED Flashes

SECURITY SYSTEM                    

OWNER’S GUIDE  

 

             

Siren Chirps on Disarm          LED Flashes                     Diagnostic

Three Chirps                                   Two Flashes                            Shock Sensor Was Activated
Three Chirps                                   Three Flashes                         Door/Hood Pin  Input Triggered
Three Chirps                                   Four Flashes                           Ignition Input Triggered     
None                                                Off                                             System Disarmed
None                                                On Solid                                   System in Valet/ Service Mode
None                                                Single Flashes                         Alarm System is Armed
None                                                Rapid Flashes                          Passive Arming Countdown
On/Off                                              Rapid Flashes                         Car Jack Mode Countdown

Summary of Contents for 640 Series









Reviews: