background image

 TRANSMITTER PROGRAMMING

SYSTEM PROGRAMMING - 

Menu 1

PAGE 28

95 SERIES

INSTALL  MANUAL

 TRANSMITTER PROGRAMMING

THE SYSTEM CAN LEARN UP TO 4 REMOTE TRANSMITTER. EACH REMOTE MUST BE 
PROGRAMMED TOGETHER DURING THE SAME SEQUENCE. FOR SECURITY 
REASONS ALL PREVIOUSLY PROGRAMMED TRANSMITTER WILL BE DELETED FROM 
MEMORY.

CYCLE THE IGNITION KEY- ON/OFF ON/OFF ON
(LEAVE THE KEY ON)

ENTERING TRANSMITTER PROGRAM MODE

PRESS AND HOLD THE PROGRAM SWITCH. THE PARK LIGHTS WILL 
TURN ON AND THE HORN WILL CHIRP 1 TIME.
CONTINUE TO HOLD THE PROGRAM SWITCH.

1 CHIRP CONFIRMS ENTERING PROGRAM MODE.
5 CHIRPS CONFIRMS TRANSMITTER PROGRAM MODE.

PRESS AND RELEASE THE LOCK BUTTON ON EACH ON THE 
REMOTE’S TO BE PROGRAMMED

THE PARK LIGHTS WILL FLASH AND THE HORN WILL CHIRP EACH 
TIME A NEW REMOTE CODE IS PROGRAMMED.

TURN THE KEY OFF TO EXIT PROGRAM MODE.

PROGRAMMING THE REMOTE’S

SYSTEM PROGRAMMING - 

Menu 1

PAGE 29

95 SERIES

INSTALL MANUAL

FAULT CODES

BRAKE FAULT

THIS FAULT WOULD OCCUR IF
THE BRAKE THERE WAS AN 
ISSUE WITH THE BRAKE 
CIRCUIT.

FAULT CODE VIA PAGER

IF THE STARTER FAILS TO START THE REMOTE WILL DISPLAY A FAULT CODE ON THE 
LCD DISPLAY. THE TEXT “FAULT” WILL BE FOLLOWED BY THE INPUT OR CONDITION 
THAT IS CAUSE THE ISSUE 

UL

TRA

FAULT

1

UL

TRA

BRAKE

1

TOGGLE

HOOD FAULT

THIS FAULT WOULD OCCUR IF 
THE HOOD WAS OPENED OR 
THE HOOD SWITCH IS BROKE 
OR OUT OF ALIGNMENT. 

UL

TRA

FAULT

1

UL

TRA

HOOD

1

TOGGLE

TACH FAULT

THIS FAULT WOULD OCCUR IF
THE VEHICLE HAD A START 
ISSUE SUCH AS A DEFECTIVE 
BYPASS MODULE. 

UL

TRA

FAULT

1

UL

TRA

TACH

1

TOGGLE

VALET FAULT

THIS FAULT WOULD OCCUR IF
THE SYSTEM WAS IN VALET 
AND YOU PRESSED START. 

UL

TRA

FAULT

1

UL

TRA

VALET

1

TOGGLE

RANGE FAULT

THIS FAULT WOULD OCCUR IF
THE USER WAS OUT OF 
OPERATING RANGE. 

UL

TRA

FAULT

1

UL

TRA

RANGE

1

TOGGLE

Summary of Contents for 3295 SERIES

































Reviews: