SYSTEM PROGRAMMING -
Menu 1
PAGE 8
95 SERIES
INSTALL MANUAL
QUICK VIEW PROGRAMMING
2ND
IGNITION
SETTING #
LED
FLASHES
SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1
2
3
4
5
6
SELECTABLE
RELAY
2ND
STARTER
2ND ACCESSORY
SPECIAL DOOR
LOCK OPTIONS
UNLOCK BEFORE / LOCK
AFTER START
LOCK AFTER STARTER
SHUT OFF
NO ADDITIONAL PULSES
GAS / DIESEL MODE
NEG GLOW PLUG / 30 SEC
DELAY
15 SECOND DELAY
GAS / POSITIVE GLOW PLUG
RE-ARM OPTIONS
PULSE WITH LOCK
PULSE AFTER START
(DEFROST / SEAT)
PULSE WITH LOCK & AFTER
SHUTDOWN
RUNTIME
4 MINUTE RUNTIME
PRESS BUTTON ONCE TO
START
45 MINUTE RUNTIME
15 MINUTE RUNTIME
REMOTE START
ACTIVATION
PRESS BUTTON TWICE TO
START
PROGRAM MODE 3
PROGRAM MODE 4
PROGRAM MODE 3 - see page 21 for detailed instructions
PROGRAM MODE 4 - see page 23 for detailed instructions
SYSTEM PROGRAMMING -
Menu 1
SYSTEM PROGRAMMING -
Menu 1
AUTO TACH / TACHLESS
SETTING #
LED FLASHES
SETTING
DESCRIPTION
OPTION 1
1 CHIRP
OPTION 2
2 CHIRPS
OPTION 3
3 CHIRPS
1
2
3
4
TACH OPTIONS
HYBRID MODE 1
ADJUST FOR OVER-
CRANK
INCREASES TACH SETTING
BY 10%
ADJUST FOR UNDER-
CRANK
DECREASE TACH SETTING
BY 10%
TACH WAIT SETTINGS
300ms TACH CHECK DELAY 750ms TACH CHECK DELAY
NO TACH CHECK DELAY
7
LEDS FLASH WHEN
LOCKED/ ARMED
LED FLASHES
LEDS DO NOT FLASH
WHEN LOCKED/ ARMED
5
BYPASS MODULE
SELECTION TYPE
FORTIN BYPASS
MODULE
IDATA LINK BYPASS
MODULE
*The default setting is for idatalink modules. For Fortin bypass modules power-
up the system with the Fortin module connected to the data port to set the default
to Fortin bypass module.
HYBRID MODE 2
SYSTEM PROGRAMMING -
Menu 1
PAGE 9
95 SERIES
INSTALL MANUAL
TACH / TACHLESS LEARNING
AUTO TACH/ TACHLESS LEARNING
Horn/ Siren will chip to confirm that
the Tach/ Tachless has been programmed.
Start the vehicle with
the ignition key.
2 CHIRPS
To Tach/ Tachless Learn the system simply start the vehicle with the ignition key. To confirm that
a proper Tach signal has been programmed the system will chirp the Horn/ Siren and flash the
park lights two times. If the tach wire is not connected the park lights will flash and the horn will
chirp 4 times to indicate Tachless Mode.
NEW- If the vehicle does not have a 12 volt starter
wire let it run for 30-35 seconds. The LEDs will flash rapidly if a proper tach is detected
then turn off when the tach programs.
***The system must be Tach Learned before remote starting***
MANUAL TACH/ TACHLESS LEARNING
Start the vehicle with
the ignition key.
SYSTEM PROGRAMMING -
Menu 1
Press and Hold
the brake pedal,
Start the vehicle
with the key then
press and release
the
program button then
hold for 5 seconds.
To confirm that a proper Tach signal has been
programmed the system will chirp the Horn/ Siren and flash the park lights two times. If the tach
wire is not connected the park lights will flash and the horn will chirp 4 times to indicate Tachless
Mode. If the Tach is not learned when the start button is pressed the park lights will flash 7 times.
***The system must be Tach Learned before remote starting***
* If Tach does not learn check for proper connection on the starter wire, ignition wire and at the
Tach connection. If the connections are good, reset the system and try again.
-
For best results connect the Tach wire to a fuel injector wire.
* If the vehicle does not start when the remote starter is activated, the park lights will flash a
diagnostic code. (See Diagnostic Chart).
**If the vehicle still does not start, check all connections and check for a factory installed Anti-
Theft system. If the Anti-Theft prevents the vehicle from starting the remote start will flash the
park lights 7 times. The system does not have to be Tach learned if this happens, simply start
the vehicle with the key and let it run for 5 seconds then turn off.
TACH NOTES
BRAKE
Hold the
brake
4 CHIRPS
Horn/ Siren will chip to confirm
that the Tach/ Tachless has been
programmed.
2 CHIRPS
4 CHIRPS
