background image

SETS OPTION 1 –TWO PRESSES-

 Press and release the start button two times to 

activate the remote starter.

SETS OPTION 2 – ONE PRESS- 

Press and release the start button one time to 

activate the remote starter.

SETS OPTION 3 – NEGATIVE PARK LIGHT- Negative output for park light flash 
feature. (DEFAULT)

SYSTEM PROGRAMMING - 

Menu 1

PAGE 22

95 SERIES

INSTALL  MANUAL

  PROGRAM MODE

CHANGE SETTING 6 - 
GOTO SETTING 7 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 6- REMOTE STARTING

THE SIREN WILL CHIRP 6 TIMES WHEN SETTING 6 IS SELECTED

6 CHIRP

PRESS 

1 TIME

6X

1 CHIRP

2 CHIRP

3 CHIRP

SETS OPTION 1 –LEDS OFF-

 No LED flashes when the doors are locked/armed.

SETS OPTION 2 – LED FLASH- The LEDs flash when the doors are lock/ armed.

CHANGE SETTING 7 - 
GOTO SETTING 1 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 7- LED FLASHES

THE SIREN WILL CHIRP 7 TIMES WHEN SETTING 7 IS SELECTED

7 CHIRP

PRESS 

1 TIME

7X

1 CHIRP

2 CHIRP

SYSTEM PROGRAMMING - 

Menu 1

ENTERING PROGRAM MODE 4

ON/OFF -  ON/OFF  - ON

(Leaving the key ON)

IGNITION KEY

PROGRAM SWITCH

1 CHIRP

Confirming

Program Mode

SIREN CHIRP

REMOTE BUTTON

Press Status 

Button to 

Select Menu 4

Press and release 1 time 

SETTING 1- TACH OPTIONS

THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED

1 CHIRP

PRESS 

1 TIME

1X

CHANGE SETTING 1 - 
GOTO SETTING 2 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETS OPTION 1 – HYBRID 1- 

The remote starter will ignore the Tach input after the 

remote start activates.

1 CHIRP

SETS OPTION 2 – HYBRID 2- 

No Tach Learn required. The starter output will stay on 

for 2 seconds then the remote starter will stay running for the programmed runtime.

2 CHIRP

SETS OPTION 3 –AUTO TACH LEARN- The system will automatically learns the 
vehicles Tach. Tachless on TL Models. (DEFAULT)

3 CHIRP

SYSTEM PROGRAMMING - 

Menu 1

PAGE 23

95 SERIES

INSTALL MANUAL

  PROGRAM MODE

1 CHIRP

CHANGE SETTING 2 - 
GOTO SETTING 3 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 2-ADJUST FOR UNDER-CRANK

THE SIREN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED

2 CHIRP

PRESS 

1 TIME

2X

1 CHIRP

Each time the HORN/ SIREN chirps the Tach setting is reduced by 10% 

SETS OPTION 1 – 300ms- 

The system will wait 300ms before starting to monitor the 

Tach input.

Each time the HORN/ SIREN chirps the Tach setting is increased by 10%

SETS OPTION 2 – 750ms-

 The system will wait 750ms before starting to monitor the 

Tach input.

 SETS OPTION 3 – NO WAIT- The system will monitor the Tach as soon as the 
vehicle has remote started. (DEFAULT)

1 CHIRP

2 CHIRP

3 CHIRP

CHANGE SETTING 4 - 
GOTO SETTING 5 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 4- TACH WAIT

THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED

4 CHIRP

PRESS 

1 TIME

4X

1 CHIRP

2 CHIRP

3 CHIRP

1 CHIRP

CHANGE SETTING 3 - 
GOTO SETTING 4 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 3-ADJUST FOR OVER-CRANK

THE SIREN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED

3 CHIRP

PRESS 

1 TIME

3X

1 CHIRP

SYSTEM PROGRAMMING - 

Menu 1

PROGRAM MODE 4

SETS OPTION 1 –FORTIN-

 Operation of Fortin bypass modules.

SETS OPTION 2 – IDATA- Operation of IDATA bypass modules.

CHANGE SETTING 5 - 
GOTO SETTING 1 - 

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 5- BYPASS SELECTION

THE SIREN WILL CHIRP 5 TIMES WHEN SETTING 7 IS SELECTED

5 CHIRP

PRESS 

1 TIME

5X

1 CHIRP

2 CHIRP

TIP- FOR FORTIN BYPASS MODULES CONNECT THE POWER TO THE REMOTE STARTER WITH THE BYPASS
MODULE CONNECTED TO SET FOR FORTIN.

Summary of Contents for 3295 SERIES

































Reviews: