background image

PIN-1 YELLOW   Starter Output-

This wire will test 0V when the key is off, in the Accessory position and when 

the Ignition is in the on position. The starter wire is 12volts during the start/ crank position only.

PIN-2 GREEN      Heater/Acc Output-

This wire will test 0V when key is off, 12volts in the ACC and iIGN 

positions and off during start/ crank position.

PIN-3 RED           12volt Input(30amp)- 

This input supplies the 12volt power for the Ignition, Park Lights  and 

the Selectable outputs. 

PIN-4 RED           12volt Input(30amp)- 

This input supplies the 12volt power for the Accessory and Starter 

outputs. 

PIN-5 BLUE         Ignition Output- 

This wire will test 0V in the off and Accessory positions the switch to12volts 

in the Ignition and Start positions.

PIN-6 WHITE       Selectable Output - 

2nd Ignition, Accessory or Start output. Programmable. (See Page 21).

Note: This output does not switch to default when the system is reset. 

PIN-1 BROWN           (+) Siren / (-) Horn (Programmable)- 

Connect this wire to the Brown or Red wire on the 

SIREN (Alarm Models) This output can be programmed to act as an additional HORN output (+)

PIN-2 ORANGE         Starter Kill/ Anti-Grind- 

This wire can be connected to an additional relay to disable the 

start circuit when the lock button is pressed. The output will also stay on when remote started, this will prevent 
the starter motor from being re-engaged while the vehicle is running.

PIN-3 WHITE             Jumper Selectable Park Light Output (+ or -)- 

Connect to the vehicles positive park light 

wire or change the jumper and connect to the vehicle negative park light wire. The default position of the jumper 
is 

Positive Park light Output.

PIN-4  BLACK

           

System Ground Input- 

Connect to chassis ground.

PIN 1- GREEN Wire- Negative Lock Output

Connect to lock wire from the switch on vehicles with a negative type switch. **LOW CURRENT ONLY**

 

PIN 2- 12volt Output for Door Lock Module

This output will supply 12volts for a plug-in type door lock module. Do not use this input to power-up relays 
**LOW CURRENT ONLY**

PIN 3- BLUE Wire- Negative Unlock Output

Connect to lock wire from the switch on vehicles with a negative type switch. **LOW CURRENT ONLY**

***SEE PAGE 24 FOR RELAY DIAGRAMS***

 

  4-PIN CONNECTOR

  4 PIN AUXILIARY SENSOR CONNECTOR

FOR MORE DETAILED INFORMATION ON PROGRAMMING, WIRING DIAGRAMS, DOOR LOCK 

CONFIGURATION AND OTHER INFORMATION, PLEASE VISIT

WWW.ULTRASTARTERS.COM/DIAGRAMS

PAGE 11

95 SERIES

  SYSTEM WIRING DETAILS

SYSTEM PROGRAMMING - 

Menu 1

INSTALL MANUAL

SYSTEM PROGRAMMING - 

Menu 1

PAGE 10

95 SERIES

INSTALL  MANUAL

  SYSTEM WIRING DETAILS

WHITE

SYSTEM GROUND INPUT

JUMPER SELECTABLE PARK LIGHT OUTPUT (+ OR -)

(+) SIREN/  HORN OUTPUT (-)  

STARTER-KILL/ ANTI-GRIND OUTPUT

BLACK

ORANGE

BROWN

BLUE

OUTPUT TO ACTIVATE IGNITION CIRCUIT

WHITE*

SELECTABLE OUTPUT (DEFAULT SECOND IGNITION)

RED

30A HIGH CURRENT 12VOLT INPUT

YELLOW

OUTPUT TO ACTIVATE START CIRCUIT 

RED

30A HIGH CURRENT 12VOLT INPUT 

GREEN

OUTPUT TO ACTIVATE ACCESSORY/ HEATER CIRCUIT

BLUE

NEGATIVE OUTPUT FOR UNLOCK

 

12+ OUTPUT FOR DOOR LOCK MODULE 

GREEN

NEGATIVE OUTPUT FOR UNLOCK

 

  

 6-PIN CONNECTOR

INSTALL  MANUAL

Summary of Contents for 3295 SERIES

































Reviews: