Ultra Start 3295 SERIES Installation Manual Download

Page: 17 / 32

SETS OPTION 1 – AUTO-LOCK & UNLOCK ENABLED-

The doors will lock when

the key is turned on and unlock the when the key is turned off.

SETS OPTION 2 – AUTO LOCK ONLY ENABLED-

The doors will lock when the key

is turned on but will not unlock when te key is turned off.

SETS OPTION 3 – AUTO LOCK DISABLED- The doors will not lock or unlock
when the key is turned on or off. (DEFAULT)

SETS OPTION 1 – HORN/ SIREN DISABLED-

The

HORN and SIREN and will

activate with Panic and Car Finder Mode only.

1 CHIRP

2 CHIRP

3 CHIRP

SYSTEM PROGRAMMING -

Menu 1

PAGE 16

95 SERIES

INSTALL MANUAL

PROGRAM MODE

CHANGE SETTING 1 -
GOTO SETTING 2 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

2 CHIRP

SETS OPTION 2 – HORN/ SIREN OUTPUT- The HORN and the SIREN* (alarm
models) output will activate for all functions. (DEFAULT)

SETS OPTION 1 – DOUBLE UNLOCK & SINGLE LOCK PULSE-

The system will

provide 2 unlock pulses w/unlock and 1 lock pulse w/lock.

1 CHIRP

SETS OPTION 2 - DOUBLE LOCK & SINGLE UNLOCK PULSE-

The system will

provide 2 lock pulses and 2 unlock pulses.

CHANGE SETTING 2 -
GOTO SETTING 3 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

CHANGE SETTING 3 -
GOTO SETTING 4 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

2 CHIRP

SETS OPTION 3 – NORMAL OPERATION- The system will pulse once for lock
and once for unlock. (DEFAULT)

3 CHIRP

CON'T ON NEXT PAGE

ENTERING PROGRAM MODE 1

ON/OFF - ON/OFF - ON

(Leaving the key ON)

IGNITION KEY

Press and release 1 time

PROGRAM SWITCH

1 CHIRP

Confirming

Program Mode

SIREN CHIRP

Press LOCK

Button to

Select Menu 1

REMOTE BUTTON

SETTING 1- IGNITION AUTO-LOCKS

THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED

1 CHIRP

PRESS

1 TIME

SETTING 2-HORN/ SIREN OUTPUT

THE SIREN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED

2 CHIRP

PRESS

1 TIME

SETTING 3-DOOR LOCK PULSES

THE SIREN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED

3 CHIRP

PRESS

1 TIME

SETS OPTION 1 - SHORT PULSES-

The output for lock and unlock is .25sec.

Helps

prevent windows from rolling up/down on some vehicles.

SETS OPTION 2 – LONG PULSES-

The output for lock and unlock is 3 seconds.

Used to activate vacuum door lock systems.

SETS OPTION 3 – NORMAL PULSES-

The output for lock and unlock is .75sec.

Used for most vehicles. (DEFAULT)

CON'T FROM PREVIOUS PAGE

SYSTEM PROGRAMMING -

Menu 1

PAGE 17

95 SERIES

INSTALL MANUAL

PROGRAM MODE

CHANGE SETTING 4 -
GOTO SETTING 5 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 4- DOOR LOCK TIMING

THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED

4 CHIRP

PRESS

1 TIME

1 CHIRP

2 CHIRP

3 CHIRP

CHANGE SETTING 5 -
GOTO SETTING 6 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 5- AUXILIARY CHANNEL 1

THE SIREN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED

5 CHIRP

PRESS

1 TIME

1 CHIRP

2 CHIRP

3 CHIRP

CHANGE SETTING 6 -
GOTO SETTING 7 -

PRESS & RELEASE THE VALET SWITCH

PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)

SETTING 6- AUXILIARY CHANNEL 2

THE SIREN WILL CHIRP 6 TIMES WHEN SETTING 6 IS SELECTED

6 CHIRP

PRESS

1 TIME

1 CHIRP

2 CHIRP

3 CHIRP

SETS OPTION 1 – NEGATIVE IGNITION OUTPUT-

Output acts as a negative ignition

output. # Activates Car Finder Mode.*

SETS OPTION 2 – DOME LIGHT SUPERVISION-

The output will activate for

30seconds when unlock is pressed. # Activates Car Finder Mode.*

SETS OPTION 3 – AUXILIARY OUTPUT- Press and hold the # button to activate
auxiliary with unlock and disarm pulse. (DEFAULT)

SETS OPTION 1 – AUXILIARY OUTPUT-

The Auxiliary output will activate by

pressing and holding the unlock and start buttons together.

SETS OPTION 2 – 2nd UNLOCK-

The output will activate when the unlock button is

pressed twice within 3 seconds.

SETS OPTION 3 – SECOND ACCESSORY OUTPUT- output acts as a negative
second accessory output. (DEFAULT)

CON'T ON NEXT PAGE

*Car Finder Mode is not available on 2way models

Summary of Contents for 3295 SERIES

































Search results

Summary of Contents for 3295 SERIES

Reviews:

Related manuals for 3295 SERIES

Brands by name

Popular brands

Ultra Start 3295 SERIES, Installation Manual

Search results

Summary of Contents for 3295 SERIES

Reviews:

Related manuals for 3295 SERIES

Brands by name

Popular brands