background image

Version 1 

 

13 

 

 

 

Adjust Shutdown Time

 

The shutdown time allows you to select the time it will take to turn the instrument off once the 
trigger is released. You may select from 1, 5, 30, 60, and 300 seconds. 

  

1. 

Enter Setup Mode…be sure to continue to hold the Trigger in.  

 
2.  Spin to Menu 03 Adjust Shutdown Time  
3. 

“Click” (press) the Sensitivity Dial in to enter  

 
4.  The Spin to the desired turn off time  
5.  Click to exit  

 

 

Menu 03

 

 

Menu 03

 

Adjust Shutdown Time

  

Adjust Shutdown Time

 

 

 

1 sec.

 

 

   

 

 

Click Spin

 

 

Menu 03

 

 

Adjust Shutdown Time

 

 

Click 

 

 
 

 

04 User Sense (Sensitivity) Defaults 

 

With experience a user will know which sensitivity level to use as the highest level. This mode 
allows the user to adjust the default starting sensitivity level for inspection routes.

 

 

To set the Sensitivity Default: 

  

1.  Enter Setup Mode be sure to continue to hold the Trigger in.  
2.  Spin to Menu 04 User Sense Defaults  
3. 

“Click” the Sensitivity Dial to Enter  

4.  Spin to the desired level (70 to 00, 70 is highest 00 is the lowest)  

 
5. 

“Click” to set  

Summary of Contents for Ultraprobe 3000




































Reviews: