background image

www.udirc.com

MADE IN CHINA

FCC Note

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving a ntenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which 

     the receiver is connected.

WARNING: Changes or modifications not expressly approved by the party 

                  responsible for compliance could void the user's authority to 

                  operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that 
      may cause undesired operation.

The equipment may generate or use radio frequency energy. Changes or 
modifications to this equipment may cause harmful interference unless the 
modifications are expressly approved in the instruction manual. Modifications not 
authorized by the manufacturer may void user’s authority to operate this device.

FCC Notice:

27

Summary of Contents for Swan U42





























Reviews: