uAvionix tailBeaconX TSO User And Installation Manual Download Page 9

Page: 9 / 46

UAV-1004270-001

Rev A

5.2 TSO Authorizations

5.2.1 tailBeaconX

tailBeaconX complies with the following TSOs when properly installed and
interfaced with equipment as detailed in this guide.

Function

TSO/RTCA/SAE

Class/Type

Air Traffic Control Radar Beacon
System/Mode Select (ATCRBS /
Mode S) Airborne Equipment

TSO-C112e

RTCA/DO-181E

Level 2els,

Class 1

[1]

Extended Squitter Automatic
Dependent Surveillance

–

Broadcast (ADS-B) and Traffic
Information Service

– Broadcast

(TIS-B) Equipment Operating on
the Radio Frequency of 1090
MHz

TSO-C166b

RTCA/DO-260B

Class B1S

Airborne Navigation Sensor
Using the Global Positioning
System (GPS) Augmented by the
Satellite Based Augmentation
System (SBAS)

TSO-C145e

INCOMP

RTCA/DO-229E

Beta 1

Position Light (White)

TSO-C30c

SAE/AS8037

Type III

[1] Anticipating RTCA/DO-181F Level 2 Transponder requirements,

tailBeaconX does not support the UM protocol, does not support the
Comm-A protocol, and does not have the capability to process and
transmit air-initiated Comm-B messages. See Section 5.4 for additional
details.

5.2.2 tailBeaconX Universal Installation Kit

tailBeaconX Universal Installation Kit complies with TSO-C30c INCOMP
when properly installed as detailed in this guide.

Summary of Contents for tailBeaconX TSO















































Search results

Summary of Contents for tailBeaconX TSO

Reviews:

Related manuals for tailBeaconX TSO

Brands by name

Popular brands

uAvionix tailBeaconX TSO, User And Installation Manual

Search results

Summary of Contents for tailBeaconX TSO

Reviews:

Related manuals for tailBeaconX TSO

Brands by name

Popular brands