uAvionix tailBeaconX TSO User And Installation Manual Download | Manualshive

Page: 20 / 46

background image

UAV-1004270-001

20

Rev A

7 Installation

7.1 Unpacking and Inspecting

Carefully unpack the device and make a visual inspection of the unit for
evidence of any damage incurred during shipment. If the unit is damaged,
notify the shipping company to file a claim for the damage. To justify your
claim, save the original shipping container and all packing materials.

7.2 Authorized Part Numbers

tailBeaconX

Item

P/N

tailBeaconX Hardware

UAV-1003648-( )

tailBeaconX / ping200X Software

UAV-1002393-( )

tailBeaconX TSO Installation Kits

Item

P/N

tailBeaconX Universal Installation Kit

UAV-1003793-( )

«
...
18
19
20
21
22
...
»

Summary of Contents for tailBeaconX TSO















































Reviews:

No comments

Related manuals for tailBeaconX TSO

Brand: JBL Pages: 29

Brand: Sangean Pages: 1

Brand: Sangean Pages: 24

Brand: Sangean Pages: 201

Brand: SANDIA aerospace Pages: 10

Brand: Sangean Pages: 78

Brand: Radio Shack Pages: 16

Brand: Uniden Pages: 12

Brand: Raymarine Pages: 99

Brand: Radio Shack Pages: 65

Brand: Saab Pages: 52

CC Solar Observer

Brand: C. Crane Pages: 16

Brand: Bush Pages: 25

Brand: Data-Linc Group Pages: 31

Brand: Durabrand Pages: 8

Brand: Arion Pages: 31

Brand: COMNET ERICSSON Pages: 32

Brand: Roberts Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands