background image

UAV-1004270-001 

 

25 

Rev A 

5.  Temporarily align the Mounting Plate to the opening, and ensure the 

depth of the cavity is sufficient to fully contain the tailBeaconX body. If 
not, follow the Spacer Mounting installation procedure in Section 
7.5.2. 

6.  Install the Mounting Plate, in the appropriate orientation for your 

aircraft, using either the supplied #4 or #6 hardware, or as defined 
below. 

a.  If the included hardware does not match the thread type of your 

aircraft, it is acceptable to use standard aviation hardware 
compatible with the thread types required, only if when 
installed, the screw heads do not protrude from the surface of 
the mounting plate as shown below. 

 

Note: Installation of the tailBeaconX must be in accordance with AC 43.13-
2B, Chapter 1. 

7.5.2 Spacer Mounting 

Aircraft with an installation cavity shallower than required to mount using 
the Direct Mounting method, or with other mounting interference issues, 
may use the spacer included with Installation Kit UAV-1003793-001. 

Follow instructions in Section 7.5.1, but additionally install the optional 
spacer between the aircraft surface and Mounting Gasket. Ensure proper 
engagement of the mounting hardware, considering the additional spacer 
thickness. 

Summary of Contents for tailBeaconX TSO















































Reviews: