u-he Bazille User Manual Download Page 61

Page: 61 / 65

TOC

TIPS & TRICKS

DC-removal

Try using a high-pass filter to remove DC from modulation sources (but remember that the HP

filter inverts signals). For an alternative using a lag generator, see

Processor Tricks

below.

Filter FM

Remember that you can also patch audio signals into the cutoff modulation sockets, not only

envelopes and LFOs etc.. You can even use the very same signal you are feeding into the filter,

or e.g. the bandpass (BP) output of the same filter.

Notch filter

(tip by xh3rv)

Try this for a polyphonic phasing effect: Mix a dry signal with a BP-filtered, inverted version of

the same signal. Frequencies within the band are removed from the original, resulting in ‘notch

filtering’’. The filter can't really make use of Gain or Resonance, it isn’t quite as versatile as a

parametric EQ's notch, but it looks like a fairly tight 24db attenuation at the cutoff point.
Comment by

lectrixboogaloo

: Try an LP instead of the BP... instant alternative HP filter.

HP bass boost

A good old trick worth mentioning here: A highpass filter can be used to boost low frequencies.

Set

Cutoff

to minimum,

Key Follow

to maximum,

Resonance

to about 30, then adjust the Cutoff.

Negative cutoff?

For extra-punchy filter envelopes, take the cutoff ‘below zero’ first by conn5V to a cutoff

modulation input (remember that the main filters have up to 4 cutoff modulation inputs).

Stacking Tricks

Height

You can make huge one-finger chords by stacking a couple of voices after setting up simple

chords with 3 or 4 oscillators. Here’s an example that sounds great with

Stack

= 2 and

Voice 2

detuning = 7.00.
Set

Tune

(Semitone) as follows:

OSC 1 +0.00

root

OSC 2 +7.00

perfect 5th

OSC 3 +15.00

minor 3rd

OSC 4

+22.00

minor 7th

Width

As mono or legato patches are unlikely to make excessive demands on your CPU, it’s always

worth checking whether your mono/legato patch sounds better with stacked voices than without.

Tip: You can easily pan two voices apart by setting

Alternate

StackVoice

as the Pan source.

Depth

Clever use of the

Stack Voice

modulator is key to making the most of Bazille’s stacking feature.

Use it to pan voices apart, to multiply LFO rates, to shift cutoff or even the sequencer’s

Rotate

value (is the mind boggling already?)

Summary of Contents for Bazille


































































Search results

Summary of Contents for Bazille

Reviews:

Related manuals for Bazille

Brands by name

Popular brands

u-he Bazille, User Manual

Search results

Summary of Contents for Bazille

Reviews:

Related manuals for Bazille

Brands by name

Popular brands