u-blox LEXI-R422, System Integration Manual

Page: 68 / 108

LEXI-R422 - System integration manual
UBX-23007449 - R02 Design-in Page 68 of 108
C1-Public
• Connect one pin of the normally-open mechanical switch integrated in the SIM connector (as the
SW2 pin in
Figure 45 ) to the GPIO6 input pin, providing a weak pull-down resistor (e.g. 470 k

, as
R2 in Figure 45 ).
• Connect the other pin of the normally-open mechanical switch integrated in the SIM connector
(SW1 pin in
Figure 45 ) to V_INT 1.8 V supply output by means of a strong pull-up resistor (e.g.
1 k  , as R1 in Figure 45 ).
•
Provide a 100 nF bypass capacitor (e.g. Murata GRM155R71C104K) at the SIM supply line ( VSIM ),
close to the related pad of the SIM connector, to prevent digital noise.
• Provide a bypass capacitor of about 22 pF to 47 pF (e.g. Murata GRM1555C1H470J) on each SIM
line (
VSIM , SIM_CLK , SIM_IO , SIM_RST ), very close to each related pad of the SIM connector, to
prevent RF coupling especially in case the RF antenna is placed closer than 10 - 30 cm from the
SIM card holder.
• Provide a low capacitance (less than 10 pF) ESD protection (as Tyco Electronics PESD0402-140)
on each externally accessible SIM line, close to each related pad of the SIM connector. The ESD
sensitivity rating of SIM interface pins is 1 kV (HBM according to JS-001-2017), so that, according
to the EMC/ESD requirements of the custom application, higher protection level can be required if
the lines are externally accessible.
• Limit capacitance and series resistance on each SIM signal to match the requirements for the SIM
interface (50 ns = maximum rise time on
SIM_CLK , 1.0 µs = maximum rise time on SIM_IO and
SIM_RST ).
LEXI-R422
H15
VSIM
J15
SIM_IO
K15
SIM_CLK
L15 SIM_RST
A11
V_INT
M15
GPIO6
SIM CARD
HOLDER
C
5
C
6
C
7
C
1
C
2
C
3
SIM card
bottom view
(contacts side)
C1
VPP (C6)
VCC (C1)
IO (C7)
CLK (C3)
RST (C2)
GND (C5)
C2 C3 C5
J1
C4
SW1
SW2
D1 D2 D3 D4 D5 D6
R2
R1
C
8
C
4
TP
Figure 45: Application circuit for the connection to a single removable SIM card, with SIM detection implemented
Reference Description Part number - Manufacturer
C1, C2, C3, C4 47 pF capacitor ceramic C0G 0402 5% 50 V GRM1555C1H470JA01 - Murata
C5 100 nF capacitor ceramic X7R 0402 10% 16 V GRM155R71C104KA01 - Murata
D1
–
D6 Very low capacitance ESD protection PESD0402-140 - Tyco Electronics
R1 1 k  resistor 0402 5% 0.1 W RC0402JR-071KL - Yageo Phycomp
R2 470 k  resistor 0402 5% 0.1 W RC0402JR-07470KL- Yageo Phycomp
J1 SIM card holder, 6 + 2 positions, with card presence switch Generic manufacturer,
as CCM03-3013LFT R102 - C&K Components
Table 29: Example of components for the connection to a single removable SIM card, with SIM detection implemented