background image

http://www.TYAN.com 

Table of Contents

 

Before You Begin............................................................................ 4 
Safety Precautions ........................................................................... 4 

Chapter 1 

Introduction ............................................................................................ 5 

1.1 Unpacking........................................................................................ 5 
1.2 Specifications .................................................................................. 8 
1.3 System 

View.................................................................................... 9 

Front View....................................................................................... 9 
Rear View ...................................................................................... 10 
System Assembly Flowchart ......................................................... 12 

Chapter 2 

Hardware Installation.......................................................................... 15 

2.1 System 

Assembly .......................................................................... 13 

Safety Considerations .................................................................... 13 
Opening the Cover......................................................................... 13 
Installing the CPU ......................................................................... 13 
Installing System Memory............................................................. 17 
Installing a Hard Disk Drive.......................................................... 19 

2.2  Adding a CD Drive........................................................................ 22 

With a Ultra ATA/100 Hard Disk Drive Installed......................... 22 
Without a Ultra ATA/100 Hard Disk Drive Installed.................... 24 

2.3 Rack 

Mounting (Option)................................................................ 24 

Cabinet Slides and Ears ................................................................. 25 
Cabinet into the Rack .................................................................... 27 
Locking Tab................................................................................... 27 

2.4 Setting 

Up 

the System ................................................................... 28 

Placing the System......................................................................... 28 
Making the Connection ................................................................. 28 
For 32-bit OS ................................................................................. 31 
For 64-bit OS ................................................................................. 32 

Chapter 3 

Software Installation ............................................................................ 33 

3.1 Installation 

Instructions for Windows............................................ 33 

Windows Installation Notes........................................................... 33 
Chipset Driver ............................................................................... 33 
VGA Driver ................................................................................... 34 
Intel Matrix Storage Manager........................................................ 34 

Summary of Contents for B5121G14S2
































































Reviews: