background image

 

20 

 

 

 

 

 

 

ONE YEAR LIMITED WARRANTY 

Turbosmart is a company built on Customer Satisfaction and Service. That is why all of our products go through regimented test procedures before they are 
packaged and shipped. Turbosmart stands behind its products for one full year after purchase. Terms of Warranty, Service and Returns are as follows: 
 

Limited Warranty: 

Turbosmart warrants its products to be free from defects in material and workmanship under normal use and if properly installed for a period 

of one year from date of purchase. If found to be defective, it will be replaced or repaired if returned prepaid along with proof of date of purchase. This shall 
constitute the sole remedy of the purchaser and the sole liability of Turbosmart to the extent permitted by law, the foregoing is exclusive and in lieu of all other 
warranties or representations whether expressed or implied, including any implied warranty of merchantability or fitness. In no event shall Turbosmart be liable 
for special or consequential damages. This warranty is only valid on products purchased from Turbosmart Authorized Dealers.  
 

Service: 

After the warranty period has expired, repair service is charged based on a minimum and maximum charge rate. (Contact Customer Service for current 

rate).  
 

Returns:

 When returning a Turbosmart product for repair, it must be accompanied by a completed Customer Warranty Form and RMA number. To access this 

form please go to our website 

www.turbosmartonline.com

 and you will find it on the Downloads page.  

 

THE TURBOSMART PLEDGE  

 

DO NOT USE ANY TURBOSMART PRODUCT UNTIL YOU HAVE CAREFULLY READ AND UNDERSTOOD THE FOLLOWING AGREEMENT. Please call if 
you  have  any  questions  or  do  not  understand  this  agreement.  Refer  to  our  brochure,  website  or  catalogue  for  terms  and  conditions  and  further  information 
regarding your product. Turbosmart appreciates your business and pride ourselves on our customer service. We are always happy to offer you advice and will 
provide you with help in any way we can. The purpose of this agreement is to avoid any problems or hard feelings. 
 
We sometimes make mistakes, as do our dealers, distributors and suppliers. Even customers can sometimes order the wrong parts. Do not use, modify, install, 
trial assemble, nick, drop, scratch or adjust any part until you first check for any damage. Damage must be reported immediately. NO EXCEPTIONS. If there are 
any components missing please contact your authorized reseller immediately upon receipt of  your shipment. Missing components must be reported within five 
(5) business days of receipt. Parts returned for any reason MUST BE IN RESALABLE CONDITION. It is YOUR responsibility, “THE CUSTOMER” to carefully 
package any returns to avoid shipping damage. Insurance is highly recommended. Credit cannot be issued for damaged goods. 

 

Warranty as to Defects 

– Australian Consumer Law 

1.1

 

We warrant for a period of twelve (12) months from the date of supply of the Goods and/or Services that if due to the fault of Turbosmart the Goods 

          

and/or Services (as the case may be) provided by Us are defective then We will, as determined by Us do one or more of the following: 

(a) 

In the case of Goods; the replacement of the Goods, the supply of equivalent Goods, the repair of the Goods, the payment of the cost of 

replacing the Goods or of acquiring equivalent Goods, or the payment of having the Goods repaired; or 
(b) 

In the case of Services; the supplying of the Services again, or the payment of the cost of having the Services supplied again. 

1.2

 

You will only be entitled to the benefit of the warranty set out in this pledge, if You have not wholly or partially caused or contributed to the defect                 

                 to the Goods by the misuse of the Goods or the failure to use the Goods in accordance with any specifications or instructions applicable to the Goods. 

1.3

 

The warranty contained in this pledge is provided by Turbosmart Pty Limited of 32 Milton Street North, Ashfield NSW 2131, Australia, Telephone:  

                

+(61) 1300 735 506

, Email

[email protected]

1.4

 

In order for a You to make a claim on the warranty You must within twelve (12) months of delivery of the Goods or Services give written notice to Us                     

                at the address specified in clause 1.3 above of the details of any defects in respect thereof. Any Goods referred to in a notice given pursuant to this    
                clause should be left in the state and condition in which they were delivered until such time as We or Our duly authorised agent have inspected the  
                Goods with such inspection to be carried out within a reasonable time after service of such notice. If the Goods are not so left in the state and 
condition  
                in which they were delivered then the You shall be deemed to have accepted the Goods and the warranty contained in this pledge shall not apply. 

1.5

 

You shall be responsible for all expenses associated with making a warranty claim under this pledge however if the Goods and/or Services are found to      

                be defective due to Our fault then We shall reimburse You for any expenses incurred by You in making a warranty claim upon receiving evidence  
                satisfactory to Turbosmart to support such expenditure. 

1.6

 

The benefits to You given by the warranty contained in this pledge are in addition to other rights and remedies of You have under a law in relation to  

                the Goods or Services to which the warranty relates.  

1.7

 

In accordance with the Australian Consumer Law We makes the following statement: 

                

“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a 

major  
                failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the 
goods  
                fail to be of acceptable quality and the failure 

does not amount to a major failure.” 

 
 

EXCEPT AS PROVIDED BY LAW, THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY, WHICH APPLIES TO TURBOSMART PRODUCT AS 
EXPRESSLY  GIVEN  IN  LIEU  OF  ANY  OTHER  WARRANTY  EXPRESSED  OR  IMPLIED,  INCLUDING  THAT  OF  MERCHANTABILITY.  ANY  IMPLIED 
WARRANTY INCLUDING THAT OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICCULAR PURPOSE IS HEREBY LIMITED BY THE SAME TERMS 
AND TIME LIMITATIONS SET FORTH IN THIS LIMITED EXPRESS WARRANTY AND OTHERWISE EXCLUDED.  
 
EXCEPT FOR THOSE OBLIGATIONS  ASSUMED HEREIN, TURBOSMART  ASSUMES NO OTHER OBLIGATIONS IN CONNECTION WITH THE SALE OF 
ITS PRODUCTS.  
 
IN  THE  EVENT  THAT  THE  INDIVIUDAL  PURCHASER  DOES  NOT  AGREE  WITH  THIS  AGREEMENT  THE  BUYER  MAY  PROMPTLY  RETURN  THIS 
PRODUCT, IN A NEW AND UN-USED CONDITION, WITH A DATED PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN SEVEN (7) DAYS 
FROM THE DATE OF PURCHASE FOR A FULL REFUND.  
 
THE  INSTALLATION  OF  THIS  PRODUCT  INDICATES  THAT  THE  INDIVIDUAL  PURCHASER  HAS  READ  AND  UNDERSTOOD  THIS  AGREEMENT  AND 
ACCEPTS ITS TERMS AND CONDITIONS. 

Happy motoring! 

The Turbosmart Team 

 
 

Turbosmart Pty Limited P.O. Box 264 Croydon, NSW 2132 Australia ABN: 69 081 069 794 

Ph: +61 1300 735 506    Fax: +61 1300 735 509    Email

[email protected]

 

www.turbosmartonline.com

 

 

Summary of Contents for E-Boost Street 40PSI





















Reviews: