manualshive.com logo in svg

Turbolock TL116, Manual

Share
Download
Turbolock TL116 Manual Download Page 8

8

     TURBOLOCK TL116

Section 3

Installation (Retrofit)

This section details installation steps needed if you are installing the TL116 on a door with a single cutout already 

made. Replacing an older fixture with a newer one is known as a retrofit. If your door has never had a lock or doorknob 

installed or otherwise has no cutout, please skip to Section 4.

• For easier installation, have another person help to hold the lock.
• Remove all parts of any old lock before installing the TL116. In some cases, the old strike plate and/or box may be used.
• For your convenience, installation instructions are broken into segments. Read and follow the instructions for both Pre-

Installation and Main Installation.

• If your door happens to have two cut-outs, check the clearance between the two. Make sure there is enough distance so that 

you may seal off any extra openings.

3.1 Pre-Installation

Part 1 - Disassemble the Lock

The TL116 comes already assembled. Before installation, release the wood 

screws and mounting screws to disassemble the lock into four main parts: 

Outside Assembly x 1, Inside Assembly x 1, Plate x 1, Latch Assembly x 1 

(Fig. 1).

(Fig. 1)

Outside Assembly

Inside Assembly

Latch Assembly

Plate

Summary of Contents for TL116





























Reviews:

No comments

Brands by name

Popular brands

Load more brands