Tuff stuff MSL-IV Assembly & Instruction Manual Download

Page: 5 / 24

FIG. 9

Secure the

Top Pulley Assembly (#5)

to the

Front

Upright (#3)

using two Hex Head Cap Screws 3/8 -16 X 4 1/4

(#99) four Flat Washers SAE 3/8 (#90) and two Nylon Insert
Lock Nuts 3/8-16 (#86). Next, secure the

Top Pulley

Assembly (#5)

onto the

Rear Upright (#4)

using one Hex

Head Cap Screw 3/8-16 X 3 (#94), two Flat Washers SAE 3/8
(#90) and one Nylon Insert Jam Lock Nut 3/8 -16 (#86).

Note

This bolt should be placed in the top hole of the

Rear Upright

(#4)

FIG. 10

Next, attach the

Pec Dec Housing (#18)

to the

Rear Upright (#4)

. secure this assembly using one Hex Head

Cap Screw 3/8 -16 X 3 1/2 (#8), two Flat Washers SAE 3/8
(#90) and one Nylon Insert Jam Lock Nut 3/8-16 (#86).

Note

This bolt should be placed in the top hole of the

Pec Dec

Housing (#18)

. Next, install one Hex Head Cap Screw 3/8-16

X 3 (#94), two Flat Washers SAE 3/8 (#90) and one Nylon
Insert Jam Lock Nut 3/8 -16 (#86) th rough the lower hole of the

Pec Dec Housing (#18)

. Finally, install the

Rubber Stopper

(#62)

and two Plastic Insert Caps 2 Sq. (#64), as shown

above.

FIG. 11

Attach the

Pec Dec Arm (#7)

to the

Pec Dec Arm/

Cam Support (#13)

and secure it using one Hex Head Cap

Screw 1/2-13 X 3 (#98), two Flat Washers SAE 1/2 (#89) and
one Nylon Insert Jam Lock Nut 1/2-13 (#88). Repeat this
procedure for the opposite Pec Dec Arm Assembly.

Note

: It is

recommended that the axle on the

Pec Dec Arm (#7)

lubricated with grease prior to assembly.

FIG. 12

Mount the assembled

Pec Dec Arms (#7)

Fig.11

to the

Pec Dec Housing (#18)

axles, as illustrated.

Note

: It is recommended that the

Pec Dec Housing (#18)

axles be lubricated with grease prior to assembly

. Next, mount

the two

Pec Dec Cams (#9)

onto the the axles of the

Pec Dec

Housing (#18)

, as shown above.

Owners’ Manual: Assembly Instructions

MSL-IV Muscle IV Home Gym

Summary of Contents for MSL-IV

























Search results

Summary of Contents for MSL-IV

Reviews:

Related manuals for MSL-IV

Brands by name

Popular brands

Tuff stuff MSL-IV, Assembly & Instruction Manual

Search results

Summary of Contents for MSL-IV

Reviews:

Related manuals for MSL-IV

Brands by name

Popular brands