Tuff stuff MSL-IV Assembly & Instruction Manual Download Page 14

Page: 14 / 24

FIG. 45

Attach a Nylon Pulley 4 1/2 Rd. (#35) to the

Front Upright (#3)

and secure it using one Hex Head Cap

Screw 3/8-16 X 3 3/4 (#75), two Flat Washers SAE 3/8 (#90),
one Nylon Insert Jam Lock Nut 3/8-16 (#86) and one

Cable

Retainer Bracket (#111)

. Then continue to route the

Lat

Cable (#14)

over the pulley as shown. Refer to

Fig. 1

on page

17 and

Fig. B

on page 18 for further detailed illustration of this

cable routing.

FIG. 46

Assemble the

Double Pulley Plates 1/8 X 2 X 9

(#21)

using two Nylon Pulleys 4 1/2 Rd. (#35), two Hex Head

Cap Screw 3/8-16 X 1 3/4 (#79), four Flat Washers SAE 3/8
(#90) and two Nylon Insert Jam Lock Nuts 3/8-16 (#86). Refer
to

Fig. 1

on page 17 for further detailed illustration of this

cable routing. Next, route the

Lat Cable (#14)

through the

Double Pulley Plates 1/8 X 2 X 9 (#21)

, as shown above.

Note

: The four holes on the

Double Pulley Plates 1/8 X 2 X 9

(#21)

are used to adjust the cable tension once the cable

routing has been completed.

FIG. 47

Insert a Nylon Pulley 4 1/2 Rd. (#35) into the

Adjustable Pulley Bracket (#26)

and secure it using one Hex

Head Cap Screw 3/8-16 X 1 3/4 (#79), two Flat Washers SAE
3/8 (#90) and one Nylon Insert Jam Lock Nut 3/8 -16 (#86).
Route the

Lat Cable (#14)

through the

Adjustable Pulley

Bracket (#26)

, as shown above.

FIG. 48

Attach the

Lat Cable (#14)

to the

Top Plate /Selecto

Bar (#58)

and secure it using one Split Bolt 1/2-13 X 1 (#51) an

one Split Washer 1/2 (#82). Refe r to

Fig. E

on page 18 for

further detailed illustration of this assembly.

Note

: Be sure this

hardware assembly is securely fastened.

MSL-IV Muscle IV Home Gym

Summary of Contents for MSL-IV

























Search results

Summary of Contents for MSL-IV

Reviews:

Related manuals for MSL-IV

Brands by name

Popular brands

Tuff stuff MSL-IV, Assembly & Instruction Manual

Search results

Summary of Contents for MSL-IV

Reviews:

Related manuals for MSL-IV

Brands by name

Popular brands