Tuff stuff MSL-IV Assembly & Instruction Manual Download | Manualshive

Page: 8 / 24

background image

FIG. 21

Locate the

Adjustable Pulley Bracket (#26)

and

thread a Hex Nut 1/2-13 (#88) and a Flat Washer SAE 1/2
(#89) onto it. Use the illustration above for further clarification
of this bolt and nut assembly. Next, insert the

Adjustable

Pulley Bracket (#26)

into the

Guide Rod Retainer (#54)

and

secure it using one Nylon Insert Jam Lock Nut 1/2 -13 (#88)
and one Flat Washer SAE 1/2 (#89).

Note

: Loosely secure the

nut to allow adjustment for cable tension later in the assembly
process.

FIG. 22

Insert the

Lat Bar Holder (#22)

into the tube-end of

the

Top Pulley Assembly (#5)

, as shown above. Secure this

assembly using one Hex Head Cap Screw 3/8 -16 X 2 1/2
(#78), two Flat Washers SAE 3/8 (#90) and one Nylon Insert
Jam Lock Nut 3/8-16 (#86).

FIG. 23

Now position the

Press Arm (#1)

to the

Top Pulley

Assembly (#5)

, as shown above. Next, press the

Pivot Axle 1

X 11 3/4 (#19)

through the holes in the

Press Arm (#1)

using

a rubber mallet hammer until it is flush with both sides.

Note

: It

is recommened that the Pivot Axle 1 X 11 3/4 (#19) be
greased prior to this assembly.

FIG. 24

At the top of each end of the

Press Arm (#1)

is a

set screw fixture. Secure the

Press Arm (#1)

using two Set

Screws 3/8-16 X 1/2 (#61). Use the Hex Key 3/16 (#50) tool for
securing the Set Screws 3/8-16 X 1/2 (#61). Next, insert two
Plastic Insert Caps 1 X 2 (#67) into the tube-ends of the

Press

Arm (#1)

.

MSL-IV Muscle IV Home Gym

7

«
...
6
7
8
9
10
...
»

Summary of Contents for MSL-IV

























Reviews:

No comments

Related manuals for MSL-IV

Brand: Harken Pages: 4

Brand: CAIRE Pages: 2

BTL PA0400 Series

Brand: Balluff Pages: 22

Micropulse BTL5 Series

Brand: Balluff Pages: 12

BNI IOW-560-W01-K022

Brand: Balluff Pages: 32

Brand: Baltic Pages: 68

Brand: Baltic Pages: 68

Max Charge MC-612

Brand: Balmar Pages: 12

BTL PA0400 Series

Brand: Balluff Pages: 204

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Jaga Pages: 32

Brand: H&S Pages: 54

Brand: Samson Pages: 2

Brand: MAKSIWA Pages: 155

Brand: VanGaa Lighting Pages: 7

GPSMAP 7400 Series

Brand: Garmin Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands