n
Turning on/off
After drilling in concrete, in intensely dusty environments it is
recommended to remove dust from ventilation openings and the drill chuck
To turn the power tool on press its switch (
6
) button and keep it pressed.
with a stream of compressed air. It will protect bearings and remove the dust
To lock the switch in on position press the lock (
4
).
obstructing motor cooling air supply.
To turn the power tool off just release the switch (
6
) button or, when it is
locked with switch lock (
4
), press it for a moment and then release it.
TRANSPORTATION:
n
Controlling the speed
The drill should be transported and stored in a box providing protection
against humidity, dust and tiny objects penetration; special care should be
By increasing or decreasing the pressure on switch (
6
) the user can control
taken to protect ventilation inlets. Small objects that get into the device can
the rotational speed steplessly.
damage the motor.
Low pressure on the switch (
6
) results in low speed. Increasing the pressure
raises the speed.
TROUBLESHOOTING GUIDE (TYPICAL PROBLEMS):
n
Setting the speed
The drill does not work:
Using rotational speed control (
5
) the user can set a desired speed. It can be
- check whether the power cord is properly connected and check fuses.
done during operation.
The drill works with interruptions or generates sparks:
Speed depends on the material drilled and working conditions and can be
- check and replace carbon brushes.
determined by performing a test.
NOTE!
Carbon brushes can be replaced only by competent electricians.
- If the power tool does not work despite being supplied from a proper
CHANGING THE DRILL CHUCK
:
power source, have the tool repaired sending it to the service center
.
The
Prior to any work on the power tool unplug it from the
addresses are provided in the warranty card.
mains socket.
The chuck installed on a right-hand/ left-hand rotating drill is fixed with a
left-hand thread bolt. Prior to changing the drill chuck, undo the screw
using a Phillips type (Ph2) screwdriver inserting it from the front through
the chuck opening.
NOTE:
A left-hand thread screw can be undone only by turning it
clockwise.
To remove the chuck (
1
) put the drill on a stable surface, e.g. on a work
bench, apply a two-hole spanner (14 mm) to notches at the spindle. Hold
the chuck with one hand and turn the spanner counterclockwise with the
other until the chuck is completely removed
(see Fig.
C
).
The drill chuck installation should be carried out in the opposite order.
No dirt is allowed on the chuck seat and spindle thread.
TIPS REGARDING OPERATION:
ź
After a longer operation at low speeds run the power tool at its maximum
speed with no load for about 3 minutes to cool it down.
ź
To drill holes in ceramic tiles set the operation mode switch (
2
) to
position «drill». Once the hole in the ceramic tile is ready, set the
operation mode switch to position «impact drill» and continue drilling in
this mode.
ź
When drilling in concrete, stone or walls hard alloy drill bits should be
used.
ź
When drilling in metal use sharp metal drill bits only.
NOTE:
Proper drill bit selection reduces vibrations during drilling, which
increases drilling efficiency considerably.
ź
When tightening/undoing screws place the bit onto the screw/nut when
the chuck is stopped.
STORAGE AND MAINTENANCE:
Generally, this power tool does not require any special maintenance. Store
the machine in a place away from children, keep it clean and protect from
humidity and dust. Storage conditions should exclude any mechanical
damage and weathering.
MANUFACTURER:
PROFIX Ltd.,
34
Marywilska Street,
03-228 Warsaw,
POLAND.
PROTECTION OF THE ENVIRONMENT:
The symbol nearby denotes that old equipment must
never be thrown away together with other waste (with the
penalty of a fine).
Hazardous components of electronic
equipment may adversely affect the natural environment and
human health.
Each household may contribute to the recovery and reuse (recycling) of old
machinery and equipment. Both in Poland and Europe a system for recovery
of used equipment either exists or is being created. The system
obliges all
organizations that sell such equipment to collect the used machinery and
appliances. Moreover, general purpose collecting points for such equipment
are available.
PICTOGRAMS:
Explanation of the icons located on the nominal plate and the information
tags
:
6
«Always wear safety goggles»
«Wear
»
hearing protection
«Wear a dust mask»
«Read this instruction before switching on the
power supply and starting the work»
The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the company
reserves the right to make amendments to the product specification without a prior notice. The images included into the
operation manual are only of the exemplary nature and may slightly differ from actual appearance of the device purchased.
This
instruction
manual
is
protected by copyright.
Copying it
without the written consent of PROFIX Co. Ltd. is prohibited.
