4
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use.
Improper power tool maintenance is a reason for many
g
)
Use auxiliary handles supplied with the tool.
Loss of control can
accidents.
cause personal injury.
f)
Cutting tools should be sharp and clean.
Keeping sharp cutting
h)
Always hold firmly the power tool with your both hands using
edges in good condition reduces the risk of jamming and facilitates
both the main and auxiliary handle keeping a stable position.
It
operation.
is safer to control your power tool with both hands.
g)
Power tools, equipment, working tools etc. should be used
i)
Turn the power tool immediately when the bit jams. Expect
according to this user's manual taking into account operating
intense vibrations that can result in a kickoff.
The bit jams when
the power tool is overloaded or is bent inside the object.
conditions and the work to be done.
Misusing a power tool can result
in dangerous situations.
j)
Always unplug the tool from the mains socket during breaks,
prior to changing bits, during repairs, cleaning or making
h)
At low temperatures and after a long brakes in operation it is
adjustments. Before you put the power tool aside make sure it
recommended to turn the power tool to operate it with no load
is completely stopped.
The bit can jam resulting in losing control over
for a few minutes to provide proper grease distribution inside
the power tool.
its driving mechanism.
k)
Do not use a power tool with its power cord damaged. Do not
i)
Use soft, damp (cannot be wet) cloth and soap to clean power
touch the power cord when damaged; in case of damaging the
tools. Do not use petrol, solvents and other agents that may
power cord during operation unplug it from the mains.
Damaged
damage your equipment
.
power cords increase the risk of electric shock.
j)
Power tools can be stored/carried after making sure that all
l)
If the power cord is damaged, it must be replaced with a special
moving components are locked and protected against release
cord available from an authorized service center.
with original devices intended for this purpose.
k)
Store power tools in a dry, dust and water-protected place.
Safety instructions when using long drill bits
:
l)
Carry your power tool in its original packaging to provide
a)
Never use a speed higher than the maximum drill bit speed.
protection against mechanical damage.
Always start drilling at a low speed and after touching the
workpiece to the drill bit.
At higher speeds, the drill bit may bend if not
m)
Keep handles and grip surfaces clean and free from oil and
in contact with the workpiece, resulting in injury.
grease.
Secure grip and control over the tool in unexpected circumstances
b
)
Push the drill bit against the workpiece in line with the drill bit.
are impossible if handles and grip surfaces are slippery.
Do not use excessive force.
Drill bits may bend, causing damage and
WARNING! General warnings regarding the use of
loss of control, which may result in injury.
power tools.
Repair
:
impact
impact
impact
–
Despite using the tool according to its intended application it is impossible to
eliminate certain residual risk factors. Considering the tool construction the
following risks may occur when operating the tool:
a)
Warranty and post-warranty repairs of its power tools are
carried out by PROFIX Service, which guarantees the best
quality or repair and use of genuine spare parts.
Each application of the tool not in line with the intended use as specified
below is strictly forbidden and makes the warranty terms null and void. The
manufacturer shall not be held responsible for possible consequential
damage that may arise due to or in connection with such application.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the surroundings.
Application of the tool in accordance with the intended use also refers to its
maintenance, storage, transportation and repairs.
Defective electric tools can be handed over for repairs exclusively to service
workshops appointed by the tool manufacturer. The tools supplied from
electric grid shall be repaired exclusively by authorized electricians.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.
check for excessive clearance. It is safer to fix the object machined in a fixing
device or a vice than holding it in your hand.
APPLICATIONS AND CONSTRUCTION:
The
drill is intended for drilling holes in wood, metal, plastics and
ceramics; its
mode is used to drill in bricks, stone and concrete. The
tool is equipped with an electronic control system and right-hand/left-hand
operation switch and is also suitable for tightening/undoing screws and
threading.
It is absolutely prohibited to use the tool in other applications.
The
drill is powered by a single-phase electric motor and is intended
for use in DIY under average load. It is not suitable for heavy duty tasks.
It is
WARNING!
IMPACT
DRILL, Additional Safety
Warnings
prohibited to use the tool to carry out operations that require using
Personal
S
afety
:
professional equipment.
a)
Wear ear protectors with impact drills.
Exposure to noise can cause
hearing loss.
b
)
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory contacting
a "live" wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
c
)
Use appropriate detectors to determine if
utility lines are
hidden in the work area or call the local utility company for
assistance.
Contact with electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Penetrating a water line causes
property damage or may cause an
electric shock.
d
)
Do not work materials containing asbestos.
Asbestos is considered
carcinogenic.
e)
Keep your workplace clean and tidy.
Material mixtures are extremely
- Touching the rotating drill bit with the hand, operator's clothes or power
dangerous. Light metal dusts can ignite or explode.
cord.
f)
Protect the object machined.
Make sure all clamps are closed and
- Burns when changing drill bits (Drill bits heat up intensely during
