Tryton TDS125B, Operating Instruction

Page: 7 / 60

7
Angle Grinder , Safety Warnings
Personal safety:
a) Release the On/Off switch and set it to the off position when
the power supply is interrupted, e. g., in case of a power
failure or when the mains plug is pulled.
This prevents
uncontrolled restarting.
b) When working stone, use dust extraction. The vacuum
cleaner must be approved for the extraction of stone dust.
Using this equipment reduces dust-related hazards.
c) Use a cutting guide when cutting stone. Without sideward
guidance, the cutting disc can jam and cause kickback.
THE SET CONTAINS:
d) When working with the machine, always hold it firmly with
ź
Grinder - 1 piece
both hands and provide for a secure stance. The power tool is
ź
Disk guard - 1 piece
guided more secure with both hands.
ź
Side handle -1 piece
e) Secure the workpiece. A workpiece clamped with clamping devices
ź
Fixing flange -1 piece
or in a vice is held more secure than by hand.
ź
Compression nut -1 piece
f) Never use the machine with a damaged cable. Do not touch
ź
Pin wrench -1 piece
the damaged cable and pull the mains plug when the cable is
ź
damaged while working. Damaged cables increase the risk of an
ź
-1 piece
electric shock .
ź
Warranty card -1 piece
CONSTRUCTION AND APPLICATIONS OF THE GRINDER :
DRAWING DESCRIPTION (see p. 2-3 ) :
The angle grinder is a hand power tool powered by a single-phase
1. Side handle
commutator-based electric motor. It comes with a side handle to be
2. Disk guard
mounted in three optional positions.
3. Compression nut
The tool is a Class 2 device (double insulation).
4. Fixing flange
The grinder is designed for grinding and cutting metal objects,
5. Rotation direction arrow
machining weld joints and, by using special tool bits (disks, brushes etc.),
6. Spindle lock button
to remove rust and polish metal surfaces.
7. On/off switch
The tool is not suitable to machine plaster surfaces or other strong dust-
8. Power cord
producing materials. Small dust particles by penetrating into the tool
9. Hex key
block ventilation spaces, which results in overheating and burning the
10 . Fixing screw
motor.
1 1 . Spindle
This electric tool is designed for jobs with medium intensity. It is not
1 2 . Disk
suitable for long-term operation under heavy duty conditions. Do never
13. Pin wrench
use the tool for applications that need use of professional
equipment.
TECHNICAL DATA:
unshielded area of the tool ;
- Scalding while the working accessory is being replaced (During its
operation the working accessories are getting extremely hot. To avoid
scalding operators must wear protecting gloves to replace the working
accessories;
- Throwing a machined part or pieces of a machined part ;
- Fracture /cracking of the working accessory;
- Damage of hearing when appropriate hearing protectors are not
used
;
- Emission dust hazardous for human health when works are carried
out in closed rooms (confined areas).
O perating instruction
Each application of the tool not in line with the intended use as specified
below is strictly forbidden and makes the warranty terms null and void.
The manufacturer shall not be held responsible for possible
consequential damage that may arise due to or in connection with such
application.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
Application of the tool in accordance with the intended use also refers to
its maintenance, storage, transportation and repairs.
Defective electric tools can be handed over for repairs exclusively to
service workshops appointed by the tool manufacturer. The tools
supplied from electric grid shall be repaired exclusively by authorized
electricians.
Proper use cannot guarantee that no residual risk will occur. Due to the
design of the machine, the following risks may occur:
- Touching of the working accessory during its operation within the
Hex key -1 piece
Rated voltage -240 220 V
Rated frequency 50 Hz
Power consumption 85 0 W
Speed 120 00 rpm
Max . disk diameter/ hole diameter 1 2 5 mm / 22 mm
Spindle thread M14
Equipment class / II
Power cord length 3 m
Weight 1,57 к g
Sound pressure level (LpA) 90,7 dB(A)
Sound power level (LwA) 101,7 dB(A)
Vibration level according to EN 60745-1
/ a
h,AG
2
(measuring tolerance – 1 , 5m/s )
Main handle Side handle
2
6,39 / 5,31 m/s
M easuring tolerance K / K
LpA LwA
3 dB(A)