Trumpf TruTool C 250 Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 22

background image

14

Setting work

E621EN_01.DOC

3.3 Changing the battery

¾

Press the locking mechanism (1) together and pull the

exchangeable battery out and upwards.

¾

Slide the exchangeable battery into the machine holder from

above until the battery locks into place.

1 Locking

mechanism

Removing the exchangeable

battery

Inserting the exchangeable

battery

Fig. 53321

«
...
12
13
14
15
16
...
»

Summary of Contents for TruTool C 250























Reviews:

No comments

Related manuals for TruTool C 250

PHLG 2000 SE - MANUEL 2

Brand: Parkside Pages: 30

Brand: Parkside Pages: 56

Brand: Parkside Pages: 53

Brand: Parkside Pages: 73

Brand: Parkside Pages: 20

PHLG 2000 SE - MANUEL 2

Brand: Parkside Pages: 5

Brand: Parkside Pages: 55

Brand: Parkside Pages: 55

Brand: Parkside Pages: 10

Brand: Parkside Pages: 288

Brand: Parkside Pages: 35

Brand: Parkside Pages: 35

Brand: Parkside Pages: 50

Brand: Parkside Pages: 45

Brand: Parkside Pages: 78

Brand: Parkside Pages: 41

Brand: Parkside Pages: 13

Brand: Gates Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands