TROY XCD MAN-EXT2000 Administrator'S Manual Download | Manualshive

Page: 115 / 252

background image

Windows NT/LAN Server Configuration 7-9

TELNET to access it and change the IP address using
the

SET IP ADDRESS

command described in Appendix

A.

4.

Set the IP address and verify the connection by using
the

ping

command with the address or name of the

TROY XCD print server. For example:

ping 192.189.207.77

or

ping xps

Again, substitute your actual name and IP address in
place of

xps

and

192.189.207.77

in the above

examples. You should get a response back from the
TROY XCD print server if the IP address has been set
and the print server is alive on the network. If you do
not, run the printer self-test as described in Chapter 2
and verify that you have entered the correct IP address.

5.

From the OS/2 desktop open the Templates folder.
Use the right mouse button to drag the Printer icon (not
the Network Printer icon) onto the desktop.

6.

The Create a Printer window should be open (if it is
not, double click on the printer icon).

-

Type in any name for the printer.

-

Select the default printer driver. If the desired
printer driver is not listed, click on the Install new
Printer Driver button and add the driver.

-

Choose the output port. IBM TCP/IP automatically
creates 8 named pipes called

\PIPE\LPD0

through

«
...
113
114
115
116
117
...
»

Summary of Contents for MAN-EXT2000





























































































































































































































































Reviews:

No comments

Related manuals for MAN-EXT2000

Brand: QMS Pages: 160

Brand: QMS Pages: 110

Brand: QMS Pages: 158

Brand: CAB Pages: 144

Brand: ABLE Pages: 26

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: Datecs Pages: 29

Brand: Partex Pages: 16

Brand: DNP Pages: 66

UniServer E3200 G3

Brand: H3C Pages: 401

Brand: Maxim Pages: 69

Aficio SP C730DN

Brand: Ricoh Pages: 100

Express5800/320Fa-L

Brand: NEC Pages: 406

Brand: IBM Pages: 110

Brand: Pathos Acoustics Pages: 26

Brand: MIMAKI Pages: 20

Brand: Tascam Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands