TROY XCD MAN-EXT2000 Administrator'S Manual Download Page 79 | Manualshive

Page: 79 / 252

background image

Novell Network Configuration 5-7

software from the TROY XCD Print Server Software
CD-ROM by clicking on the Start button and selecting
Run. Click on Browse and select the CD-ROM drive.
Open the Utilities folder, open the XAdmin32 folder,
and click on

SETUP.EXE

, Click OK twice and follow

the instructions on the screen.

2. Click on Start, select Programs, select the XAdmin32

folder, and then select XAdmin32.

3. Click on the IPX/SPX icon under Filters to set the

operating mode to IPX/SPX (TCP/IP mode will not
allow you to configure NetWare print queues directly).
The TROY XCD external print server should appear in
the list of available printers (the name will one of the
ones listed in the Default Print Server Names section at
the beginning of this chapter). If it does not, try going
to the menu bar and selecting Devices and then Search
Active Devices.

Important Note:

V3.59 and earlier firmware do not

support more than one service and one port (the
firmware version is listed on the self-test page). If you
have an XConnect II or XConnect 100 and need to use
the serial port for printing, you must upgrade to a
newer revision of the firmware.

4. Double click on the printer that you wish to configure,

enter the configuration password (ACCESS is the
default), and press OK.

5. A series of index card tabs will be displayed. Click on

the NetWare P1 tab to configure the first parallel port,
the NetWare S1 tab to configure the serial port, the

«
...
77
78
79
80
81
...
»

Summary of Contents for MAN-EXT2000





























































































































































































































































Reviews:

No comments

Related manuals for MAN-EXT2000

Brand: Canon Pages: 18

Brand: Canon Pages: 16

Brand: Canon Pages: 39

Brand: Canon Pages: 2

Brand: Canon Pages: 73

Brand: Canon Pages: 29

Brand: Canon Pages: 16

Brand: Canon Pages: 44

Brand: Canon Pages: 60

Brand: Olympus Pages: 236

I450 - i 450 Color Inkjet Printer

Brand: Canon Pages: 13

BladeCenter HS23

Brand: IBM Pages: 36

Brand: Samsung Pages: 9

Bixolon SRP-500

Brand: Samsung Pages: 27

550N - CLP Color Laser Printer

Brand: Samsung Pages: 288

2 COLOR THERMAL PRINTER SRP-275

Brand: Samsung Pages: 8

Brand: Samsung Pages: 6

Brand: Samsung Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands