TROY XCD MAN-EXT2000 Administrator'S Manual Download | Manualshive

Page: 161 / 252

background image

PrintraNet Internet Printing 13-3

attachment and prints it out on the printer. As a configurable
option, the remote print server can send an E-mail message back
to notify the sending PC that the job was successfully printed.

The remote print server must be running Version 3.38 or later
firmware. This firmware is available at no charge on the TROY
XCD web site (

http://www.troyxcd.com

directory).

PrintraNet is supported by all TROY XCD print servers except
the XConnect II Lite and XJet III.

A new feature of PrintraNet is its Address Book capability.
This capability allows the Windows user to have a pre-
defined list of remote printers. A print job can be sent to
any of these remote printers by simply clicking on the
appropriate address book entry. In addition, groups of
remote printers can be defined, so that a single print job can
be sent to multiple printers.

Another new feature of PrintraNet is direct E-mail printing.
This feature allows ordinary text E-mail messages to be
sent to the print server and then printed out on the printer.
No special software (other than an E-mail program) is
required on the sending computer.

This chapter covers the following topics:

•

Installation of the PrintraNet software on a Windows 95/

98/NT PC at the local site

•

Enabling the PrintraNet capability on the TROY XCD

print server at the remote site.

The manual assumes that you have already installed the
TROY XCD print server at the remote site with a valid IP
address per the instructions in the appropriate print server

«
...
159
160
161
162
163
...
»

Summary of Contents for MAN-EXT2000





























































































































































































































































Reviews:

No comments

Related manuals for MAN-EXT2000

Brand: Oki Pages: 40

870 - SuperScript B/W Laser Printer

Brand: NEC Pages: 8

Express5800/T110g-S

Brand: NEC Pages: 34

Brand: Oki Pages: 215

DiMAGE Scan Elite 5400 II

Brand: Konica Minolta Pages: 38

SUPERSERVER 6034H-X8R

Brand: Supermicro Pages: 128

Brand: IEI Technology Pages: 89

Brand: Citizen Pages: 4

System x3250 M3 Type 4251

Brand: IBM Pages: 32

Brand: Gigabyte Pages: 115

Brand: IBM Pages: 110

SuperServer 6026TT-HIBQF

Brand: Supero Pages: 112

Brand: Mita Pages: 134

Brand: HandTop Pages: 97

totalstorage fastt100

Brand: IBM Pages: 160

Brand: Canon Pages: 342

Brand: Canon Pages: 454

Brand: Canon Pages: 498

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands